INSTALLATION
Removal / installation · Vehicles built from Aug 2013
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
| 1. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH |
![]() ![]() |
Connect the belt with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not allow the anchor part of the rear No. 1 seat outer belt to overlap the protruding parts of the seat cushion frame.
Text in Illustration *a
Protruding Part
| 2. INSTALL REAR NO. 2 SEAT HINGE COVER RH |
Attach the 3 claws to install the cover.
| 3. INSTALL REAR NO. 2 SEAT HINGE COVER LH |
Attach the 3 claws to install the cover.
| 4. INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH |
Temporarily install the under cover to the seat cushion frame.
| 5. INSTALL REAR SEAT CUSHION SUPPORT SPRING |
Install the spring to the seat cushion frame
- HINT:
- Use the same procedure for both springs.
| 6. INSTALL FOLD SEAT LEG LOCK CUSHION |
![]() ![]() |
Install the cushion to the protector.
- HINT:
- Use the same procedure for both cushions.
| 7. INSTALL REAR SEAT CUSHION EDGE PROTECTOR |
Install the protector to the cushion frame.
- HINT:
- Use the same procedure for both protectors.
| 8. INSTALL REAR SEAT HINGE SUB-ASSEMBLY RH |
Install the hinge.
Install the pin to the hinge.
Install a new E-ring.
| 9. INSTALL REAR SEAT STAY SUB-ASSEMBLY |
Connect the seat stay ball-joint to the seat hinge.
- HINT:
- It is only necessary to perform this step when replacing the seat stay and seat hinge. After the seat stay is connected to the seat hinge, it cannot be disconnected.
| 10. INSTALL REAR SEAT HINGE SUB-ASSEMBLY LH |
Install the spring of the seat stay ball-joint.
Temporarily install the seat hinge and seat stay as a unit.
Raise the under cover.
Connect the seat stay to the seat cushion frame.

Connect the reclining release handle to the under cover.

Install the 5 screws.
Attach the 10 claws to install the under cover.
Install the pin to the hinge.
Install a new E-ring.
| 11. INSTALL REAR SEAT HINGE PAWL GUIDE |
Attach the 4 claws to install the pawl guide.
- HINT:
- Use the same procedure for both pawl guides.
| 12. INSTALL SEAT TRACK OPEN LEVER PIN SUB ASSEMBLY |
![]() ![]() |
Install the pin as shown in the illustration.
Install the stopper.
- HINT:
- Use the same procedure for both pins.
| 13. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Attach the 2 claws to install the cover.
Install the 2 screws.
| 14. INSTALL REAR NO. 2 SEAT CUSHION |
Attach the 2 hooks.
Attach the guide and 2 claws to install the cover.

Install the 2 screws.
| 15. INSTALL REAR NO. 1 SEAT RECLINING COVER RH |
Attach the 2 hooks.
Attach the guide and 2 claws to install the cover.

Install the 2 screws.
| 16. INSTALL REAR SEAT RECLINING COVER LH |
Attach the guide and 2 claws to install the cover.

Install the 2 screws.
| 17. INSTALL REAR NO. 1 SEAT ASSEMBLY LH |
Install the rear No. 1 seat assembly LH (Click here).



