2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
  1. Remove the rear No. 1 seat assembly LH (Click here).


2. REMOVE REAR SEAT RECLINING COVER LH

B241078
  1. Remove the 2 screws.

  1. Using a moulding remover, detach the 2 claws.

  1. Move the cover in the direction of the arrow to detach the guide and remove the cover.


3. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

B241100
  1. Remove the 2 screws.

  1. Using a moulding remover, detach the 2 claws.

  1. Move the cover in the direction of the arrow to detach the guide.

  1. B241102
    Detach the 2 hooks and remove the cover.


4. REMOVE REAR NO. 2 SEAT CUSHION

B241103
  1. Remove the screw and cushion.


5. REMOVE REAR RECLINING ADJUSTER INSIDE COVER LH

B241104
  1. Remove the 2 screws.

  1. Detach the 2 claws and remove the cover.


6. REMOVE SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY

B241080
  1. Using a screwdriver, remove the stopper.

  1. Remove the pin as shown in the illustration.

    HINT:
    Use the same procedure for both pins.


7. REMOVE REAR SEAT HINGE PAWL GUIDE

B241082
  1. Detach the 4 claws and remove the pawl guide.

    HINT:
    Use the same procedure for both pawl guides.


8. REMOVE REAR SEAT HINGE SUB-ASSEMBLY LH

  1. B241088
    Using a screwdriver, remove the E-ring.

  1. B241089
    Remove the pin.

  1. B241105
    Using a screwdriver, detach the 10 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B241106
    Remove the 5 screws.

  1. Disconnect the reclining release handle from the under cover.

  1. Raise the under cover.

  1. B241090
    Using a screwdriver, remove the spring of the seat stay ball-joint.

  1. Disconnect the seat stay from the seat cushion frame.

  1. Remove the seat hinge and seat stay as a unit.

    NOTICE:
    The seat stay cannot be disconnected from the seat hinge. If the stay is disconnected from the hinge, replacement of both parts is necessary.

    HINT:
    If it is necessary to replace the seat hinge, replace it together with the seat stay as the stay cannot be disconnected from the hinge.


9. REMOVE REAR SEAT STAY SUB-ASSEMBLY

HINT:
  1. As the seat stay cannot be disconnected from the seat hinge, it is removed in the previous step.
  2. If it is necessary to replace the seat stay, replace it together with the seat hinge as the stay cannot be disconnected from the hinge.


10. REMOVE REAR SEAT HINGE SUB-ASSEMBLY RH

  1. B241083
    Using a screwdriver, remove the E-ring.

  1. B241084
    Remove the pin and hinge.


11. REMOVE REAR SEAT CUSHION EDGE PROTECTOR

B241085
  1. Remove the protector from the cushion frame.

    HINT:
    Use the same procedure for both protectors.


12. REMOVE REAR SEAT CUSHION SUPPORT SPRING

B242241
  1. Remove the spring from the seat cushion frame.

    HINT:
    Use the same procedure for both springs.


13. REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH
  1. Remove the under cover.


14. REMOVE REAR NO. 2 SEAT HINGE COVER LH

B241049
  1. Detach the 3 claws and remove the cover.


15. REMOVE REAR NO. 2 SEAT HINGE COVER RH
  1. Detach the 3 claws and remove the cover.


16. REMOVE SEAT CUSHION COVER WITH PAD

  1. B241092E01
    Cut off the tack pins and remove the carpet from the cushion pad.
    Text in Illustration 
    *1
    Tack Pin

  1. B241107
    Remove the hog rings and seat cushion cover with pad.


17. DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY ANCHOR LH

  1. B241112
    Remove the bolt and disconnect the belt.


18. REMOVE REAR SEATBACK COVER

B237641
  1. Using a screwdriver, detach the 8 claws and remove the 2 covers.

    HINT:
    Tape the screwdriver tip before use.


19. REMOVE NO. 1 SEATBACK PAD LH

  1. B241112
    Remove the bolt and disconnect the outer belt.

  1. B241113E01
    Detach the fastening tape and open the cover.
    Text in Illustration 
    *1
    Fastening Tape

  1. B242242
    Remove the 6 hog rings.

  1. B241114
    Open the 2 fasteners, and then open the seatback cover.

  1. B241116
    Remove the seatback pad.


20. REMOVE REAR SEAT INNER RECLINING COVER RH

B241117
  1. Remove the screw.

  1. Detach the guide and remove the cover.


21. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY

B241119
  1. Remove the 2 bolts, center armrest and bush.


22. REMOVE REAR SEAT CENTER ARMREST HINGE

B241120
  1. Remove the screw and armrest hinge.


23. REMOVE REAR SEAT ARMREST SUPPORT

B241121
  1. Remove the armrest support.


24. REMOVE SHOULDER BELT ANCHOR COVER

B241122E01
  1. Using a screwdriver, detach the 2 claws and 2 guides, and then remove the cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


25. REMOVE REAR SEAT SHOULDER BELT HOLE COVER LH

  1. B241124
    Detach the 4 claws and remove the cover.

  1. B241125
    Disconnect the outer belt.


26. REMOVE REAR SEATBACK LOCK STRIKER COVER

B237663E01
  1. Using a screwdriver, detach the claw and guide, and then remove the cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


27. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

  1. B237665
    Remove the 2 screws.

  1. B165025E02
    Disconnect the cable in the order shown in the illustration and remove the lever.


28. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B241127
  1. Detach the 8 claws and remove the 4 supports.


29. REMOVE SEATBACK COVER WITH PAD

  1. B241093
    Detach the 2 hooks and remove the seatback cover with pad.

  1. B241129
    Disconnect the outer belt from the seatback cover with pad.


30. REMOVE SEPARATE TYPE REAR SEATBACK COVER

  1. Remove the hog rings and detach the fastening tape, and then remove the seatback cover from the seatback pad.

    B241130E01

    Text in Illustration 
    *1
    Fastening Tape
    -
    -


31. REMOVE REAR SEAT INNER RECLINING COVER RH

B241132
  1. Detach the 2 claws and remove the cover.


32. REMOVE RECLINING ADJUSTER COVER LH

B241134
  1. Remove the 4 screws.

  1. Detach the 4 claws and remove the cover.


33. REMOVE REAR SEAT SHOULDER BELT GUIDE

  1. B241137
    Detach the 2 claws and open the cover.

  1. B241138
    Disconnect the seat belt from the belt guide.

  1. B241168
    Detach the 4 guides and remove the belt guide.


34. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

  1. B244721
    Remove the 3 nuts and belt sensor.

  1. B244722
    Remove the nut and seat belt.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →