2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH
  1. Install the cable to the seat cushion frame.

  1. Attach the 3 cable clamps and connect the cable.

  1. Install 2 new cable ties.


2. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH
  1. Install the seatback frame with the 4 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }


3. INSTALL REAR SEAT RECLINING COVER INNER LH
  1. Attach the 2 guides to install the cover.


4. INSTALL REAR SEAT RECLINING COVER INNER RH
  1. Attach the 2 guides to install the cover.


5. INSTALL REAR SEAT INNER RECLINING COVER LH
  1. Attach the 2 guides and 2 claws to install the cover.


6. INSTALL REAR SEAT INNER RECLINING COVER RH
  1. Attach the 2 guides and 2 claws to install the cover.


7. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
  1. Install the cable to the seatback frame.

  1. Attach the 2 cable clamps and connect the cable.


8. INSTALL SEPARATE TYPE REAR SEATBACK COVER

B241065E01
  1. Install the seatback cover with 2 new hog rings and attach the fastening tape.

    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Fastening Tape

  1. Using hog ring pliers, install new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


9. INSTALL SEATBACK COVER WITH PAD
  1. Attach the 2 hooks to install the seatback cover with pad.


10. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
  1. Attach the 4 claws to install the 2 supports.


11. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH

B165053E02
  1. Connect the cable in the order shown in the illustration to install the lever.

  1. Install the 2 screws.


12. INSTALL REAR SEATBACK LOCK STRIKER COVER

B237755
  1. Attach the guide and claw to install the cover.


13. INSTALL NO. 1 SEATBACK PAD RH
  1. Install the seatback pad.

  1. B241060
    Close the 2 fasteners, and then close the seatback cover.

  1. B241058E01
    Using hog ring pliers, install 3 new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

  1. Attach the 3 fastening tapes and close the cover.


14. INSTALL REAR SEATBACK COVER
  1. Attach the 4 claws to install the cover.


15. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

B241055E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


16. INSTALL REAR SEAT INNER CUSHION EDGE PROTECTOR RH
  1. Install the protector with new tack pins.


17. INSTALL SEAT CUSHION COVER WITH PAD

B241052E01
  1. Using hog ring pliers, install the seatback cover with pad with new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

  1. Install the carpet with new tack pins.


18. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

  1. B242886E01
    Remove the nut and inner belt.


19. INSTALL REAR NO. 2 SEAT HINGE COVER LH
  1. Attach the 3 claws to install the cover.


20. INSTALL REAR NO. 2 SEAT HINGE COVER RH
  1. Attach the 3 claws to install the cover.


21. INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY RH
  1. Temporarily install the under cover to the seat cushion frame.


22. INSTALL REAR SEAT CUSHION SUPPORT SPRING
  1. Install the spring to the seat cushion frame.

    HINT:
    Use the same procedure for both springs.


23. INSTALL FOLD SEAT LEG LOCK CUSHION

B241041
  1. Install the cushion to the protector.

    HINT:
    Use the same procedure for both cushions.


24. INSTALL REAR SEAT CUSHION EDGE PROTECTOR
  1. Install the protector to the cushion frame.

    HINT:
    Use the same procedure for both protectors.


25. INSTALL REAR SEAT STAY SUB-ASSEMBLY
  1. Connect the seat stay ball-joint to the seat hinge.

    HINT:
    It is only necessary to perform this step when replacing the seat stay and seat hinge. After the seat stay is connected to the seat hinge, it cannot be disconnected.


26. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
  1. Install the spring of the seat stay ball-joint.

  1. Temporarily install the seat hinge and seat stay as a unit.

  1. Raise the under cover.

  1. B241048
    Connect the seat stay to the seat cushion frame.

  1. B241046
    Connect the reclining release handle to the under cover.

  1. Install the 4 bolts.

  1. Attach the 6 claws to install the under cover.

  1. Install the pin to the hinge.

  1. Install a new E-ring.


27. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
  1. Install the hinge.

  1. Install the pin to the hinge.

  1. Install a new E-ring.


28. INSTALL REAR SEAT HINGE PAWL GUIDE
  1. Attach the 4 claws to install the pawl guide.

    HINT:
    Use the same procedure for both pawl guides.


29. INSTALL SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY

B241035
  1. Install the pin as shown in the illustration.

  1. Install the stopper.

    HINT:
    Use the same procedure for both pins.


30. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B241033
  1. Move the cover in the direction of the arrow to attach the guide.

  1. Attach the 2 claws.

  1. Install the cover with the 2 screws.


31. INSTALL REAR NO. 1 SEAT RECLINING COVER LH
  1. Attach the 2 hooks.

  1. B241030
    Move the cover in the direction of the arrow to attach the guide.

  1. Attach the 2 claws.

  1. Install the cover with the 2 screws.

← DISASSEMBLY (from Aug 2013)INSTALLATION (from Aug 2013) →