2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here)

3. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


4. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A245857E01

    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


7. REMOVE FRONT WHEEL LH

8. REMOVE FRONT FENDER APRON SEAL LH
  1. Remove the 5 clips and front fender apron seal LH.


9. REMOVE INJECTOR DRIVER ASSEMBLY

  1. A239612
    Disconnect the 4 connectors.

  1. Remove the 2 bolts and injector driver assembly.


10. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A239651
    Remove the 3 bolts and disconnect the vane pump oil reservoir.


11. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE

  1. A244615
    Disconnect the 3 vacuum switching valve connectors.

  1. A244965
    Disconnect the No. 1 vacuum transmitting hose.

  1. A244967
    Disconnect the 2 No. 2 vacuum transmitting hoses from the No. 2 EGR valve.

  1. A244966
    Disconnect the No. 1 vacuum transmitting hose and No. 4 vacuum transmitting hose.

  1. A244968
    Remove the 2 bolts and manifold stay with vacuum switching valve.


12. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A245462
    Remove the bolt and No. 2 injection pipe clamp.

  1. A239672E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
    Text in Illustration 
    *a
    Common Rail Side
    *b
    Fuel Supply Pump Side


13. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the injection pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the injection pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A244613
    Remove the 2 nuts and No. 3 injection pipe clamp.

  1. A244612
    Remove the 2 bolts and 2 No. 2 injection pipe clamps.

  1. A239673E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side


14. DISCONNECT HEATER WATER PIPE SUB-ASSEMBLY

  1. A239652
    Detach the water by-pass hose clamp.

  1. Remove the bolt and disconnect the heater water pipe.


15. REMOVE WATER BY-PASS HOSE
  1. Detach the 4 water by-pass hose clamps.

  1. Disconnect the No. 7 water by-pass hose labeled A in the illustration.

  1. Disconnect the No. 4 water by-pass hose labeled B in the illustration.

  1. Disconnect the No. 3 water by-pass hose labeled C in the illustration.

  1. Disconnect the No. 8 water by-pass hose labeled D in the illustration.

  1. Disconnect the No. 6 water by-pass hose labeled E in the illustration.

  1. Disconnect the No. 5 water by-pass hose labeled F in the illustration.

    A239653E01


16. REMOVE NO. 1 VACUUM TRANSMITTING PIPE

  1. A244611
    Disconnect the vacuum hose from the intake manifold.

  1. Remove the bolt and No. 1 vacuum transmitting pipe.


17. REMOVE WIRING HARNESS CLAMP BRACKET
  1. Disconnect the glow plug connector.

  1. A245469
    Detach the 2 wire harness clamps and disconnect the glow plug connector from the wiring harness clamp bracket.

  1. A245466
    Remove the bolt and wiring harness clamp bracket.


18. REMOVE NO. 3 ENGINE COVER BRACKET

  1. A239350
    Remove the 2 nuts and No. 3 engine cover bracket.


19. REMOVE ENGINE COVER BRACKET INSULATOR

  1. A239397
    Remove the 2 nuts and 2 engine cover bracket insulators.


20. REMOVE NO. 4 ENGINE COVER BRACKET

  1. A239426
    Remove the bolt and No. 4 engine cover bracket.


21. REMOVE AIR CONNECTOR STAY

  1. A245685
    Disconnect the 4 injector connectors and detach the 3 wire harness clamps.

  1. A239654E01
    Remove the bolt labeled A and disconnect the No. 1 fuel pipe from the air connector stay.
    Text in Illustration 
    *1
    No. 1 Fuel Pipe

  1. Remove the 3 bolts and air connector stay.


22. REMOVE EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY

  1. A239655
    Disconnect the fuel pressure sensor connector from the common rail.

  1. Remove the 4 nuts, 3 bolts and EGR cooler with No. 2 EGR valve.

  1. Remove the 2 gaskets from the cylinder head and electric EGR control valve.

    A239656E01

    Text in Illustration 
    *1
    Gasket
    -
    -


23. REMOVE EGR VALVE ADAPTER

  1. A239641
    Using a 6 mm hexagon wrench, remove the 3 hexagon bolts, 3 plate washers, EGR valve adapter and gasket.


24. REMOVE NO. 2 EGR VALVE ASSEMBLY

  1. A239642
    Remove the bolt, No. 2 EGR valve and gasket.


25. REMOVE EGR COOLER INSULATOR

  1. A239643E01
    Remove the 2 EGR cooler insulators from the EGR cooler.
    Text in Illustration 
    *1
    No. 2 EGR Cooler Insulator
    *2
    No. 1 EGR Cooler Insulator

← REMOVAL (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →