2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

B157D DAB Tuner Antenna Disconnected

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna assembly which is connected to the radio and display receiver assembly.
DTC Code
DTC Detection Condition
Trouble Area
B157D
The digital audio broadcasting antenna assembly is not connected
  1. Digital audio broadcasting antenna assembly
  2. No. 2 antenna cord sub-assembly
  3. Radio and display receiver assembly
  4. Harness or connector

WIRING DIAGRAM

E286269E02

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

    OK:
    Optional components are installed.

    NOTICE:
    Do not remove optional components without permission of the customer.



NG
Go to step 3
OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. INSPECT WINDSHIELD GLASS ANTENNA WIRE
  1. Inspect the windshield glass antenna wire (Click here).



NG
REPAIR WINDSHIELD GLASS ANTENNA WIRE (Click here)
OK


4. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Remove the antenna connector from the radio and display receiver assembly.

  1. Turn the engine switch on (ACC) with the radio and display receiver assembly connector connected.

  1. Turn on the radio and turn into AM mode.

  1. Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

    OK:
    Noise occurs.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 ANTENNA CORD SUB-ASSEMBLY)
  1. Disconnect the DB radio and display receiver assembly connector.

  1. Disconnect the antenna connector from the No.2 antenna cord sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 1
    Always
    Below 1 Ω
    1-a - 1-a
    Always
    Below 1 Ω
    1 - Body ground
    Always
    10 kΩ or higher
    1-a - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

  1. E286153E01
    Disconnect the antenna connector from the radio and display receiver assembly.

  1. Disconnect the antenna connector from the digital audio broadcasting antenna assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 1
    Always
    Below 1 Ω
    1-a - 1-a
    Always
    Below 1 Ω
    1 - Body ground
    Always
    10 kΩ or higher
    1-a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Digital Audio Broadcasting Antenna Assembly LH)
    *b
    Front view of wire harness connector
    (to Vehicle Wire Harness)



NG
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


7. CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH
  1. Replace the digital audio broadcasting antenna assembly LH with a known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
Go to step 8
OK

END (DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH IS DEFECTIVE)

8. CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY RH
  1. Replace the digital audio broadcasting antenna assembly RH with a known good one (Click here ).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY RH IS DEFECTIVE)


← B157D DAB Tuner Antenna Disconnected (Aug 2013 – Jul 2014)B157E Bluetooth Antenna Disconnected (Aug 2013 – Jul 2014) →