Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to terminal IGSW of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A357165E02
5.844,2.635 6.333,2.823 0.49,0.188 10 false IGSW 5.438,2.719 5.854,2.885 0.417,0.167 10 false G180 4.979,2.854 5.323,3 0.344,0.146 10 false IGN 5.865,3.438 6.24,3.677 0.375,0.24 10 false +B2 5.438,3.448 5.802,3.656 0.365,0.208 10 false G180 5.656,2.552 5.792,2.729 0.135,0.177 10 false 8 5.646,3.26 5.854,3.448 0.208,0.188 10 false 2 5.458,3.823 5.875,4.021 0.417,0.198 10 false G180 5.885,3.802 6.208,3.969 0.323,0.167 10 false +B 5.885,4.198 6.406,4.396 0.521,0.198 10 false MREL 5.448,4.188 5.844,4.375 0.396,0.188 10 false G181 5.448,4.583 5.833,4.76 0.385,0.177 10 false G153 5.896,4.583 6.125,4.781 0.229,0.198 10 false E1 6.198,5.063 6.583,5.26 0.385,0.198 10 false ECM 4.25,2.719 4.51,2.865 0.26,0.146 10 false 1A 4.354,2.563 4.563,2.729 0.208,0.167 10 false 5 4.25,3.083 4.573,3.271 0.323,0.188 10 false 1A 4.344,2.906 4.51,3.073 0.167,0.167 10 false 1 4.26,3.833 4.573,4 0.313,0.167 10 false 1B 4.344,3.656 4.521,3.854 0.177,0.198 10 false 4 4.25,4.188 4.51,4.354 0.26,0.167 10 false 1B 4.344,4.01 4.51,4.167 0.167,0.156 10 false 2 3.646,3.375 3.969,3.552 0.323,0.177 10 false IG2 3.635,4.49 3.906,4.677 0.271,0.188 10 false EFI 2.854,3.917 3.125,4.104 0.271,0.188 10 false EFI 2.844,2.802 3.167,2.979 0.323,0.177 10 false IG2 2.198,3.083 2.417,3.219 0.219,0.135 10 false 1A 2.219,2.885 2.438,3.031 0.219,0.146 10 false 3 2.219,3.833 2.521,4.01 0.302,0.177 10 false 1C 2.219,3.646 2.333,3.813 0.115,0.167 10 false 1 2.208,4.188 2.448,4.333 0.24,0.146 10 false 1B 2.219,4.01 2.365,4.156 0.146,0.146 10 false 3 3.021,4.802 4.531,5.031 1.51,0.229 10 false No. 1 Integration Relay 0.844,4.823 1.333,4.979 0.49,0.156 10 false Battery 1.063,3.229 1.563,3.458 0.5,0.229 10 false P/I-B 2.073,1.948 4.469,2.125 2.396,0.177 10 false Power Management Control ECU*1 0.885,1.448 1.229,1.604 0.344,0.156 10 false AM2 2.177,1.656 2.49,1.823 0.313,0.167 10 false G51 2.177,1.313 2.49,1.49 0.313,0.177 10 false G51 2.333,1.125 2.49,1.292 0.156,0.167 10 false 2 2.323,1.469 2.479,1.656 0.156,0.188 10 false 1 2.521,1.281 2.917,1.438 0.396,0.156 10 false AM21 2.51,1.646 2.927,1.844 0.417,0.198 10 false AM22 3.115,1.479 3.479,1.677 0.365,0.198 10 false IG2D 3.49,1.469 3.844,1.625 0.354,0.156 10 false G50 2.333,0.625 2.594,0.802 0.26,0.177 10 false G2 2.333,0.76 4.24,0.979 1.906,0.219 10 false Ignition Switch Assembly*2 2.49,0.385 2.802,0.563 0.313,0.177 10 false AM2 3.198,0.385 3.479,0.552 0.281,0.167 10 false IG2 2.323,0.156 2.469,0.323 0.146,0.167 10 false 7 3.521,0.156 3.677,0.313 0.156,0.156 10 false 6 1.344,0.438 1.583,0.625 0.24,0.188 10 false ST 5.646,3.625 5.76,3.781 0.115,0.156 10 false 1 5.646,4.01 5.792,4.156 0.146,0.146 10 false 6 5.646,4.417 5.813,4.573 0.167,0.156 10 false 3 3.51,1.281 3.656,1.458 0.146,0.177 10 false 8 5.073,0.438 7,0.635 1.927,0.198 10 false *1: W/ Entry and Start System 5.083,0.854 7.125,1.125 2.042,0.271 10 false *2: W/o Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C153-3 (E1) - Body ground Always Below 1 Ω




OK

2.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)

2.INSPECT ECM (IGSW VOLTAGE)
U169555E02
2.083,1.885 1.313,2.479 false 2.573,1.813 3.052,2.031 0.479,0.219 10 false G180 0.938,2.521 1.604,2.792 0.667,0.271 10 false 8(IGSW) 0.25,0.104 0.583,0.25 0.333,0.146 10 false *a

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G180-8 (IGSW) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

3.INSPECT NO. 1 INTEGRATION RELAY (EFI RELAY)

NG

8.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
3.INSPECT NO. 1 INTEGRATION RELAY (EFI RELAY)
a.

Inspect the NO. 1 integration relay (EFI relay) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI RELAY)

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - ECM)
a.

Remove the NO. 1 integration relay (EFI relay) from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-4 - G180-1 (+B) Always Below 1 Ω
1B-4 - G180-2 (+B2) Always Below 1 Ω
1B-4 or G180-1 (+B) - Body ground Always 10 kΩ or higher
1B-4 or G180-2 (+B2) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - ECM)

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - BATTERY)
a.

Remove the NO. 1 integration relay (EFI relay) from the engine room relay block.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - Positive battery terminal Always Below 1 Ω
1C-1 or Positive battery terminal - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - BATTERY)

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - BODY GROUND)
a.

Remove the NO. 1 integration relay (EFI relay) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-3 - Body ground Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - BODY GROUND)

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - ECM)
a.

Disconnect the ECM connector.


b.

Remove the integration relay (EFI relay) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-2 - G181-6 (MREL) Always Below 1 Ω
1B-2 or G181-6 (MREL) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (EFI RELAY) - ECM)

8.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Inspect the NO. 1 integration relay (IG2 relay) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2 RELAY)

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - ECM)
a.

Disconnect the ECM connector.


b.

Remove the NO. 1 integration relay (IG2 relay) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-5 - G180-8 (IGSW) Always Below 1 Ω
1A-5 or G180-8 (IGSW) - Body ground Always 10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - ECM)

10.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BATTERY)
a.

Remove the NO. 1 integration relay (IG2 relay) from the engine room relay block.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - Positive battery terminal Always Below 1 Ω
1C-1 or Positive battery terminal - Body ground Always 10 kΩ or higher




OK

11.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BATTERY)

11.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)
a.

Remove the NO. 1 integration relay (IG2 relay) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-3 - Body ground Always Below 1 Ω




OK

12.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)

12.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
a.

Confirm the entry and start system.

Result
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

B

14.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - IGNITION SWITCH)
13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G50-8 (IG2D) - 1A-1 Always Below 1 Ω
G50-8 (IG2D) or 1A-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

14.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - IGNITION SWITCH)
a.

Disconnect the ignition switch connector.


b.

Remove the NO. 1 integration relay (IG2 relay) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-1 - G2-6 (IG2) Always Below 1 Ω
1A-1 or G2-6 (IG2) - Body ground Always 10 kΩ or higher




OK

15.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - IGNITION SWITCH)

15.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>2TR-FE (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY