Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the park/neutral position switch (for automatic transmission) or clutch start switch (for manual transmission) and also flows to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

This chart is based on the premise that the engine can be cranked normally. If the engine does not crank normally, proceed to Problem Symptoms Table (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
a.

Confirm the vehicle specifications.


Result:
Result Proceed to
w/o Entry and Start System A
w/ Entry and Start System B



A

2.READ VALUE USING GTS

B

14.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.


e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.


OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK ST RELAY (POWER SOURCE)
3.CHECK ST RELAY (POWER SOURCE)

Remove the ST relay from the engine room relay block assembly.

A356320E01
0.128,0.157 0.355,0.339 0.227,0.182 10 *1 0.777,2.073 0.952,2.212 0.175,0.139 10 *2

a.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 2 - Body ground Engine cranking 11 to 14 V


HINT:

The engine does not crank because the relay is not installed.


Text in Illustration
*1 Engine Room Relay Block Assembly
*2 ST Relay

Result:
Result Proceed to
OK A
NG (for Manual Transmission Models) B
NG (for Automatic Transmission Models) C



A

4.INSPECT RELAY (ST RELAY)

B

6.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY, ECM)

C

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY, ECM)
4.INSPECT RELAY (ST RELAY)

OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPLACE RELAY (ST RELAY)

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (for Manual Transmission Models) A
OK (for Automatic Transmission Models) B
NG C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH PEDAL SWITCH)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY, ECM)
a.

Remove the ST relay from the engine room relay block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 - A41-1 Always Below 1 Ω
ST relay terminal 2 - C154-17 (STA) Always Below 1 Ω
ST relay terminal 2, A41-1 or C154-17 (STA) - Body ground Always 10 kΩ or higher



OK

7.INSPECT CLUTCH START SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (See page)Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION.



OK

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
G2-1 (ST1) - A41-2 Always Below 1 Ω
G2-1 (ST1) or A41-2 - Body ground Always 10 kΩ or higher



OK

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.


OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY, ECM)
a.

Remove the ST relay from the engine room relay block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
C159-5 (L) - ST relay terminal 2 Always Below 1 Ω
C154-17 (STA) - ST relay terminal 2 Always Below 1 Ω
C159-5 (L), C154-17 (STA) or ST relay terminal 2 - Body ground Always 10 kΩ or higher



OK

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.


OK

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)

NG

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ignition switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
G2-1 (ST1) - C159-4 (B) Always Below 1 Ω
G2-1 (ST1) - C154-15 (NSW) Always Below 1 Ω
G2-1 (ST1), C159-4 (B) or C154-15 (NSW) - Body ground Always 10 kΩ or higher



OK

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See pageEngine / Hybrid System>2TR-FE (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

14.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.


e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.


OK:
Ignition Switch Position Starter Signal
ON OFF
START ON


Result:
Result Proceed to
NG A
OK B



A

15.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

15.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.


OK

16.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)

NG

16.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)
a.

Remove the ST relay from the engine room relay block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 - C159-5(L) Always Below 1 Ω
ST relay terminal 2 - C154-17 (STA) Always Below 1 Ω
ST relay terminal 2, C159-5 (L) or C154-17 (STA) - Body ground Always 10 kΩ or higher



OK

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
G50-3 (STAR) - C159-4 (B) Always Below 1 Ω
G50-3 (STAR) - C154-15 (NSW) Always Below 1 Ω
G50-3 (STAR) or C159-4 (B) or C154-15 (NSW) - Body ground Always 10 kΩ or higher



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR