Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260500 ENGINE UNIT A

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 2.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly.


b.

Remove the gasket from the oil filler cap sub-assembly.


Hide 11301M 4.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11301M 5.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11101J 7.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 11101J 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11201 9.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12233 10.REMOVE NO. 1 VENTILATION CONNECTOR

a.
A340619

Remove the 2 bolts and No. 1 ventilation connector from the cylinder head cover sub-assembly.


Hide 12144 14.REMOVE OIL PAN COVER SILENCER

Hide 12102A 15.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 17.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A336470

Remove the 6 bolts, oil strainer sub-assembly and gasket.


Hide 11421 18.REMOVE OIL PAN STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 11381 19.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A346835E01
0.185,1.276 0.376,1.449 0.191,0.173 10 *a 0.4,1.375 0.598,1.375 0.598,1.375 1.52,1.014 false

Remove the 6 bolts.


b.

Using a screwdriver, pry out the rear engine oil seal retainer.

Text in Illustration
*a Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 11381A 20.REMOVE REAR ENGINE OIL SEAL

a.
A101332E05
2.115,0.787 2.309,0.988 0.194,0.201 10 *a 1.719,1.144 2.01,0.909 2.01,0.909 2.1,0.909 false 0.848,1.696 1.012,1.877 0.164,0.181 10 *b 1.238,1.689 1.057,1.82 1.057,1.82 1.697,1.982 false

Place the rear engine oil seal retainer on wooden blocks.

Text in Illustration
*a Protective Tape
*b Wooden Blocks


b.

Using a screwdriver and hammer, tap out the rear engine oil seal.

HINT:

Tape the screwdriver tip before use.



Hide 83530 21.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 16281 25.REMOVE NO. 4 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A356070

Slide the 2 clips and remove the No. 4 water by-pass hose from the oil cooler assembly and union.


Hide 16288 26.REMOVE NO. 4 WATER BY-PASS PIPE (w/ Oil Cooler)

a.
A356069E03
0.719,1.646 0.719,0.927 false 3.146,1.365 3.052,1.365 3.052,1.365 2.708,1.167 true 3.177,1.271 3.406,1.51 0.229,0.24 10 true *2 0.656,1.688 0.885,1.906 0.229,0.219 10 false *1

Disconnect the No. 5 water by-pass hose from the oil cooler assembly.

Text in Illustration
*1 No. 4 Water By-pass Pipe
*2 No. 5 Water By-pass Hose


b.

Remove the 2 bolts and No. 4 water by-pass pipe.


Hide 15710 27.REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)

Hide 15600A 28.REMOVE OIL FILTER UNION (w/o Oil Cooler)

a.
A356071

Using a 27 mm socket wrench, remove the oil filter union.


Hide 15609 29.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

a.
U149537E04
1.01,1.146 1.167,1.344 0.156,0.198 10 false .

Remove the 2 bolts and nut from the oil filter bracket.


b.

Remove the 2 screw plugs and 2 gaskets from the oil filter bracket.


c.
A356072E01
2.554,0.436 2.753,0.629 0.200,0.193 10 *1 1.018,2.541 1.218,2.734 0.200,0.193 10 *2 1.992,2.623 1.245,2.623 false 2.52,0.533 2.353,0.533 2.353,0.533 1.205,0.742 false

Remove the oil filter bracket gasket and O-ring.

Text in Illustration
*1 O-Ring
*2 Oil Filter Bracket Gasket


d.
A384444

Using a hexagon wrench, remove the oil filter bracket union.


Hide 15777E 30.REMOVE UNION (w/ Oil Cooler)

a.
A356073

Remove the union from the cylinder block.


Hide 11432A 31.REMOVE NO. 1 TAPER SCREW PLUG (w/o Oil Cooler)

a.
A346834

Remove the No. 1 taper screw plug from the cylinder block.


Hide 16620D 32.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11302 33.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16100 34.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 11301C 35.REMOVE TIMING CHAIN CASE OIL SEAL

Hide 36.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.


b.
U147706E03
1,0.802 1.146,1.313 1.146,1.313 1.417,1.313 false 1.125,0.583 1.333,1.302 false 2.698,0.688 2.438,0.25 2.438,0.25 2.208,0.25 false 2.708,0.917 2.302,0.25 false 2.49,2.344 2.729,2.021 2.729,2.021 2.802,2.021 true 0.896,2.313 0.625,1.958 0.625,1.958 0.542,1.958 true 2.74,3.688 2.354,3.688 2.354,3.688 1.771,3.896 true 2.063,4.417 2.063,4.271 2.063,4.271 1.844,4.042 true 1,0.052 1.219,0.24 0.219,0.188 10 true *b 1.438,1.229 1.646,1.448 0.208,0.219 10 false *a 2.021,0.146 2.24,0.375 0.219,0.229 10 false *a 2.823,1.896 3.021,2.115 0.198,0.219 10 false *a 0.344,1.844 0.552,2.042 0.208,0.198 10 false *a 1.99,4.438 2.188,4.635 0.198,0.198 10 false *a 2.76,3.594 2.979,3.802 0.219,0.208 10 false *1 1.75,3.302 1.969,3.5 0.219,0.198 10 false *c

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

Text in Illustration
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Approximately 13°
*c Approximately 30°

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



c.

Remove the crankshaft pulley bolt.


Hide 11204 37.REMOVE CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

a.
A336454

Remove the 2 bolts and cylinder head cover connector sub-assembly.


b.

Remove the No. 2 camshaft bearing cap oil hole gasket and 3 No. 3 camshaft bearing cap oil hole gaskets from the No. 1 camshaft bearing cap.


Hide 13566B 38.REMOVE TIMING CHAIN GUIDE

a.
A336451E01
0.444,1.426 0.625,1.586 0.180,0.159 10 *1 0.647,1.512 0.773,1.512 0.773,1.512 1.53,1.041 false

Remove the 2 bolts, timing chain guide and O-ring.

Text in Illustration
*1 O-Ring


Hide 13540 39.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

When the No. 1 chain tensioner assembly is removed, do not rotate the crankshaft.

·

When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.



a.
A101303E26
2.292,0.813 2.604,0.313 2.604,0.313 2.698,0.313 true 1.771,1.552 1.938,1.896 1.938,1.896 2.063,1.896 true 0.521,1.823 0.521,1.51 false 2.74,0.219 2.948,0.417 0.208,0.198 10 false *a 2.094,1.802 2.323,1.99 0.229,0.188 10 false *b 0.458,1.844 0.677,2.021 0.219,0.177 10 false *c

Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.

Text in Illustration
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.


c.
A340033

Remove the bolt, nut, No. 1 chain tensioner assembly and gasket.


Hide 13559 40.REMOVE CHAIN TENSIONER SLIPPER

a.
A340035

Remove the bolt and chain tensioner slipper.


Hide 13561 41.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A340037

Remove the bolt, nut and No. 1 chain vibration damper.


Hide 13506 42.REMOVE CHAIN SUB-ASSEMBLY

Hide 13521 43.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A101308

Remove the crankshaft timing gear or sprocket from the crankshaft.


Hide 13801 47.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13050 50.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13050 51.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 52.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13070A 53.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 15678A 56.REMOVE OIL CONTROL VALVE FILTER

a.
A101413

Using an 8 mm hexagon wrench, remove the screw plug.


b.

Remove the oil control valve filter and gasket.


Hide 13562 57.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A101320E11
1.01,1.177 0.844,1.927 0.844,1.927 0.688,1.927 false 0.625,1.219 0.385,0.656 0.385,0.656 0.24,0.656 false 0.042,0.583 0.219,0.781 0.177,0.198 10 false *a 0.448,1.833 0.646,2.031 0.198,0.198 10 false *b

Move the stopper plate downward to release the lock and push the plunger deep into the tensioner.

Text in Illustration
*a Plunger
*b Stopper Plate


b.

Move the stopper plate upward to set the lock and insert a hexagon wrench into the stopper plate hole.


c.
A384445

Remove the bolt and No. 2 chain vibration damper.


Hide 13563 58.REMOVE NO. 3 CHAIN VIBRATION DAMPER

a.
A384435

Remove the 2 bolts and No. 3 chain vibration damper.


Hide 13550 59.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A384434

Remove the hexagon wrench from the No. 2 chain tensioner assembly.


b.

Remove the nut and No. 2 chain tensioner assembly.


Hide 13507 60.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

a.
A101324

Remove the bolt, balanceshaft drive gear shaft and balanceshaft drive gear sub-assembly.


b.

Remove the crankshaft timing sprocket and No. 2 chain sub-assembly.


Hide 13554 61.REMOVE NO. 4 CHAIN VIBRATION DAMPER

a.
A384446

Remove the 2 bolts and No. 4 chain vibration damper.


Hide 13471A 62.REMOVE CRANKSHAFT PULLEY SET KEY

a.
A101326

Remove the 2 crankshaft pulley set keys from the crankshaft.