Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A240424E48
4.375,1.167 6.198,1.344 1.823,0.177 10 false 5 V Constant Voltage Circuit 5.354,1.99 6.365,2.406 1.01,0.417 10 false Microprocessor 1.688,1.469 2.74,1.719 1.052,0.25 10 false from EFI Relay 1.344,1.135 2.688,1.302 1.344,0.167 10 false from EFI NO. 2 Fuse 2.906,1.042 3.427,1.26 0.521,0.219 10 false BATT 0.302,1.958 2.625,2.542 2.323,0.583 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.302,2.948 2.635,3.427 2.333,0.479 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.135 4.333,3.344 0.26,0.208 10 false R 2.958,1.396 3.313,1.625 0.354,0.229 10 false +B 3.167,2.333 3.458,2.563 0.292,0.229 10 false VC 4.885,0.354 5.333,0.583 0.448,0.229 10 false ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A356321E04
0.594,0.656 1.052,0.854 0.458,0.198 10 false C13 0.604,7.594 1.063,7.792 0.458,0.198 10 false C137 0.594,6.073 1.052,6.271 0.458,0.198 10 false C140 0.594,4.646 1.052,4.844 0.458,0.198 10 false C139 0.604,2.344 1.063,2.542 0.458,0.198 10 false A19 0.604,0.833 1.74,1.26 1.135,0.427 10 false Throttle Body with Motor Assembly 0.604,2.521 1.771,2.948 1.167,0.427 10 false Accelerator Pedal Sensor Assembly 2.74,0.615 3.094,0.813 0.354,0.198 10 false VC 0.615,7.771 1.938,8 1.323,0.229 10 false Air Pressure Sensor 0.594,6.25 2.229,6.604 1.635,0.354 10 false Camshaft Position Sensor (for Exhaust Side) 0.594,4.823 2.219,5.208 1.625,0.385 10 false Camshaft Position Sensor (for Intake Side) 2.75,0.99 3.104,1.188 0.354,0.198 10 false E2 2.656,1.344 3.01,1.542 0.354,0.198 10 false VTA 2.594,1.708 3.01,1.927 0.417,0.219 10 false VTA2 2.552,2.219 3.073,2.469 0.521,0.25 10 false VCPA 2.563,2.573 3.094,2.813 0.531,0.24 10 false VCP2 2.635,2.938 3.073,3.177 0.438,0.24 10 false VPA 2.573,3.302 3.115,3.594 0.542,0.292 10 false VPA2 2.635,3.656 2.99,3.854 0.354,0.198 10 false EPA 2.563,4.021 3.083,4.271 0.521,0.25 10 false EPA2 2.74,4.656 3.094,4.854 0.354,0.198 10 false VC 2.625,5.385 3.052,5.635 0.427,0.25 10 false VVI+ 2.656,5.01 3.01,5.208 0.354,0.198 10 false VVI- 2.594,6.479 3.063,6.74 0.469,0.26 10 false VVE- 2.563,6.844 3.021,7.042 0.458,0.198 10 false VVE+ 2.656,6.135 3.01,6.333 0.354,0.198 10 false VC2 2.74,7.625 3.094,7.823 0.354,0.198 10 false VC 2.76,7.99 3.115,8.188 0.354,0.198 10 false E2 2.708,8.354 3.063,8.552 0.354,0.198 10 false AIP 3.073,2.844 3.26,3.052 0.188,0.208 10 false 6 3.063,2.469 3.219,2.667 0.156,0.198 10 false 1 3.094,5.271 3.25,5.469 0.156,0.198 10 false 1 3.073,7.865 3.302,8.063 0.229,0.198 10 false 1 3.094,6.719 3.25,6.917 0.156,0.198 10 false 1 3.094,8.24 3.281,8.448 0.188,0.208 10 false 2 3.094,4.906 3.281,5.115 0.188,0.208 10 false 2 3.094,6.375 3.281,6.583 0.188,0.208 10 false 2 3.083,3.917 3.271,4.125 0.188,0.208 10 false 2 3.083,0.865 3.271,1.073 0.188,0.208 10 false 3 3.073,3.198 3.26,3.406 0.188,0.208 10 false 3 3.094,4.542 3.281,4.75 0.188,0.208 10 false 3 3.083,6.01 3.271,6.219 0.188,0.208 10 false 3 3.073,7.5 3.26,7.708 0.188,0.208 10 false 3 3.073,2.094 3.26,2.302 0.188,0.208 10 false 4 3.094,1.594 3.281,1.802 0.188,0.208 10 false 4 3.083,0.5 3.271,0.708 0.188,0.208 10 false 5 3.073,3.552 3.26,3.76 0.188,0.208 10 false 5 3.083,1.229 3.271,1.438 0.188,0.208 10 false 6 4.885,0.615 5.5,0.813 0.615,0.198 10 false C153 4.885,0.979 5.5,1.177 0.615,0.198 10 false C153 4.896,1.344 5.51,1.542 0.615,0.198 10 false C153 4.896,1.708 5.51,1.906 0.615,0.198 10 false C153 4.896,4.667 5.51,4.865 0.615,0.198 10 false C153 4.896,5.021 5.51,5.219 0.615,0.198 10 false C153 4.896,5.385 5.51,5.583 0.615,0.198 10 false C153 4.896,6.135 5.51,6.333 0.615,0.198 10 false C153 4.896,6.49 5.51,6.688 0.615,0.198 10 false C153 4.896,6.854 5.51,7.052 0.615,0.198 10 false C153 4.885,7.625 5.5,7.823 0.615,0.198 10 false C153 4.875,7.99 5.49,8.188 0.615,0.198 10 false C153 4.885,8.354 5.5,8.552 0.615,0.198 10 false C153 4.896,2.208 5.51,2.406 0.615,0.198 10 false G180 4.896,2.573 5.51,2.771 0.615,0.198 10 false G180 4.896,2.938 5.51,3.135 0.615,0.198 10 false G180 4.896,3.302 5.51,3.5 0.615,0.198 10 false G180 4.896,3.667 5.51,3.865 0.615,0.198 10 false G180 4.896,4.031 5.51,4.229 0.615,0.198 10 false G180 5.042,0.427 5.354,0.625 0.313,0.198 10 false 29 5.042,0.792 5.365,1.01 0.323,0.219 10 false 28 5.042,1.156 5.354,1.354 0.313,0.198 10 false 30 5.042,1.531 5.354,1.729 0.313,0.198 10 false 18 5.031,2.021 5.344,2.219 0.313,0.198 10 false 20 5.031,2.396 5.344,2.594 0.313,0.198 10 false 22 5.031,2.76 5.344,2.958 0.313,0.198 10 false 26 5.031,3.115 5.344,3.313 0.313,0.198 10 false 28 5.031,3.479 5.344,3.677 0.313,0.198 10 false 27 5.031,3.844 5.344,4.042 0.313,0.198 10 false 29 5.042,4.469 5.354,4.667 0.313,0.198 10 false 21 5.042,4.844 5.354,5.042 0.313,0.198 10 false 22 5.042,5.208 5.354,5.406 0.313,0.198 10 false 23 5.042,5.938 5.354,6.135 0.313,0.198 10 false 31 5.031,6.313 5.344,6.51 0.313,0.198 10 false 32 5.042,6.677 5.354,6.875 0.313,0.198 10 false 24 5.052,7.438 5.365,7.635 0.313,0.198 10 false 20 5.042,7.813 5.354,8.01 0.313,0.198 10 false 25 5.042,8.177 5.354,8.375 0.313,0.198 10 false 26 5.333,0.531 5.948,0.729 0.615,0.198 10 false VCTA 5.333,0.896 5.792,1.094 0.458,0.198 10 false ETA 5.333,1.333 5.948,1.531 0.615,0.198 10 false VTA1 5.333,1.698 5.948,1.896 0.615,0.198 10 false VTA2 5.333,2.125 5.948,2.323 0.615,0.198 10 false VCPA 5.333,2.49 5.948,2.688 0.615,0.198 10 false VCP2 5.333,2.927 5.792,3.125 0.458,0.198 10 false VPA 5.333,3.271 5.948,3.469 0.615,0.198 10 false VPA2 5.333,3.594 5.948,3.792 0.615,0.198 10 false EPA 5.333,3.948 5.948,4.146 0.615,0.198 10 false EPA2 5.333,4.573 5.948,4.771 0.615,0.198 10 false VCV1 5.333,4.948 5.948,5.146 0.615,0.198 10 false VV1- 5.344,5.375 5.958,5.573 0.615,0.198 10 false VV1+ 5.333,6.063 5.948,6.26 0.615,0.198 10 false VCE1 5.333,6.417 5.948,6.615 0.615,0.198 10 false EV1- 5.333,6.844 5.948,7.042 0.615,0.198 10 false EV1+ 5.333,7.542 5.948,7.74 0.615,0.198 10 false VCAI 5.333,7.906 5.948,8.104 0.615,0.198 10 false EAIP 5.344,8.344 5.958,8.542 0.615,0.198 10 false AIP 5.813,9.135 6.427,9.333 0.615,0.198 10 false ECM

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
U169501E02
2.354,0.667 1.823,1.76 false 2.458,0.677 2.813,1.76 false 1.958,0.115 2.354,0.292 0.396,0.177 10 false G180 0.115,0.094 0.333,0.281 0.219,0.188 10 false *a 1.615,1.792 2.104,1.969 0.49,0.177 10 false 2(+B2) 2.625,1.792 3.031,1.99 0.406,0.198 10 false 1(+B)

a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G180-1(+B) - Body ground Ignition switch ON 11 to 14 V
G180-2(+B2) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)

HINT:

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B

HINT:

Perform "Inspection After Repair" after cleaning the throttle body (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (AIR PRESSURE SENSOR)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (AIR PRESSURE SENSOR)
a.

Disconnect the air pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE))

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE))
a.

Disconnect the camshaft position sensor (for intake side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST SIDE))

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE)

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST SIDE))
a.

Disconnect the camshaft position sensor (for exhaust side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK HARNESS AND CONNECTOR

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST SIDE)

9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the air pressure sensor connector (with air pressure sensor).


d.

Disconnect the mass air flow meter sub-assembly connector.


e.

Disconnect the camshaft position sensor (for intake side) connector.


f.

Disconnect the camshaft position sensor (for exhaust side) connector.


g.

Disconnect the ECM connectors.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C153-29 (VCTA) - Body ground Always 10 kΩ or higher
G180-20 (VCPA) - Body ground Always 10 kΩ or higher
G180-22 (VCP2) - Body ground Always 10 kΩ or higher
C153-20 (VCAI) - Body ground Always 10 kΩ or higher
C153-31 (VCE1) - Body ground Always 10 kΩ or higher
C153-21 (VCV1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR