Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  


DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor (EV1 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The exhaust camshaft has 3 teeth on its outer circumference.

When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends the camshaft angle data to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0365 There is no camshaft position sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust side) circuit

·

Camshaft position sensor (for exhaust side)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


P0367 Output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust side) circuit

·

Camshaft position sensor (for exhaust side)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


P0368 Output voltage of the camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust side) circuit

·

Camshaft position sensor (for exhaust side)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM



A255508E35
0.052,0.031 0.656,0.188 0.604,0.156 10 false 5 V/DIV. 0.219,0.771 0.615,0.979 0.396,0.208 10 false VV1 0.198,1.563 0.594,1.792 0.396,0.229 10 false EV1 3.052,0.813 3.396,0.958 0.344,0.146 10 false GND 3.052,1.573 3.396,1.719 0.344,0.146 10 false GND 1.271,1.865 2.021,2.042 0.75,0.177 10 false 20 ms./DIV.

Reference: Inspection using an oscilloscope

HINT:
·

The correct waveforms are as shown.

·

VV1 stands for the camshaft position sensor (for intake side) signal and EV1 stands for the camshaft position sensor (for exhaust side) signal.

Terminal No. (Symbol) Tool Setting Condition
C153-23 (VV1+) - C153-22 (VV1-) 5 V/DIV, 20 ms/DIV Idling
C153-24 (EV1+) - C153-32 (EV1-) 5 V/DIV, 20 ms/DIV Idling




MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the camshaft revolving, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0365, P0367 or P0368.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A240394E13
1.044,1.911 1.459,2.095 0.415,0.184 10 C140 1.044,2.061 3.903,2.254 2.860,0.193 10 Camshaft Position Sensor (for Exhaust Side) 5.182,0.417 5.578,0.563 0.397,0.147 10 VCE1 5.182,0.949 5.604,1.105 0.422,0.156 10 EV1+ 5.182,1.496 5.555,1.651 0.373,0.156 10 EV1- 5.705,2.201 6.131,2.375 0.427,0.174 10 C153 5.705,2.364 6.046,2.548 0.341,0.184 10 ECM 4.915,0.365 5.198,0.549 0.283,0.184 10 31 4.897,0.96 5.108,1.163 0.211,0.202 10 24 4.894,1.46 5.183,1.625 0.289,0.165 10 32 2.651,0.363 2.773,0.526 0.121,0.163 10 3 2.651,0.899 2.752,1.076 0.100,0.177 10 1 2.651,1.435 2.759,1.584 0.107,0.149 10 2 2.234,0.363 2.563,0.540 0.330,0.177 10 VC2 2.165,0.899 2.550,1.062 0.385,0.163 10 VVE+ 2.193,1.435 2.564,1.598 0.371,0.163 10 VVE- 1.611,0.899 1.746,1.069 0.135,0.170 10 * 0.065,2.376 4.395,2.560 4.330,0.184 10 *: MRE (Outputs a voltage corresponding to changes in magnetic flux)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (SENSOR POWER SOURCE)
a.
U169146E02
1.958,1.344 2.271,1.677 false 0.458,1.24 0.813,1.406 0.354,0.167 10 false C140 2.313,1.688 2.771,1.854 0.458,0.167 10 false VC2 0.083,0.042 0.271,0.208 0.188,0.167 10 false *a

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C140-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to Camshaft Position Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor (for exhaust side) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C140-1 (VVE+) - C153-24 (EV1+) Always Below 1 Ω
C140-2 (VVE-) - C153-32 (EV1-) Always Below 1 Ω
C140-1 (VVE+) or C153-24 (EV1+) - Body ground Always 10 kΩ or higher
C140-2 (VVE-) or C153-32 (EV1-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST SIDE)
a.
A208464E40
0.604,1.792 1.229,2.042 0.625,0.25 10 false OK 2.667,1.802 3.354,2.052 0.688,0.25 10 false NG 1.719,1.563 2.438,1.844 0.719,0.281 10 false Clearance

Check the camshaft position sensor (for exhaust side) installation.

OK:

Camshaft position sensor is installed correctly.




OK

4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)

NG

4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the exhaust camshaft (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

5.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST SIDE)

NG

5.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST SIDE)
a.

Replace the camshaft position sensor (for exhaust side) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
P0365, P0367 or P0368 is output B

HINT:

If the engine does not start, replace the ECM.




A

7.CHECK ENGINE MECHANICAL SYSTEM

B

END

7.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
P0365, P0367 or P0368 is output B

HINT:

If the engine does not start, replace the ECM.




A

B

CHECK FOR INTERMITTENT PROBLEMS

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor (for exhaust side) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C140-3 (VC2) - C153-31 (VCE1) Always Below 1 Ω
C140-3 (VC2) or C153-31 (VCE1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR