Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › CAMSHAFT › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260506 CAMSHAFT A

2TR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 11201 11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11204 12.REMOVE CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

Hide 14.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A337700E10
1,0.854 1.229,1.417 1.229,1.417 1.333,1.417 false 1.229,1.417 1.115,0.646 false 2.708,1 2.292,0.385 2.292,0.385 2.177,0.385 false 2.292,0.385 2.719,0.771 false 2.469,2.396 2.906,2.063 2.906,2.063 3.063,2.063 false 0.865,2.385 0.479,2.125 0.479,2.125 0.302,2.125 false 1.833,4.208 2.521,4.083 2.521,4.083 2.656,4.083 false 1.021,0.052 1.25,0.271 0.229,0.219 10 true *c 1.365,1.323 1.594,1.552 0.229,0.229 10 false *a 1.958,0.229 2.167,0.469 0.208,0.24 10 true *a 0.083,2.01 0.313,2.219 0.229,0.208 10 false *a 3.094,1.958 3.313,2.177 0.219,0.219 10 false *a 2.698,3.99 2.938,4.188 0.24,0.198 10 false *b

Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover sub-assembly.


b.

Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the No. 1 bearing cap as shown in the illustration.

Text in Illustration
*a Timing Mark
*b Groove
*c Approximately 13°

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



Hide 13540 15.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A337701E04
0.385,0.51 0.542,0.51 0.542,0.51 0.875,0.813 true 2.938,0.49 2.813,0.49 2.813,0.49 2.49,0.823 true 0.26,1.125 0.396,1.125 0.396,1.125 0.896,0.885 true 3.156,1.063 3.042,1.063 3.042,1.063 2.5,0.927 true 0.188,0.396 0.406,0.604 0.219,0.208 10 false *a 2.969,0.385 3.177,0.583 0.208,0.198 10 false *a 0.052,1.021 0.281,1.219 0.229,0.198 10 false *b 3.177,0.969 3.385,1.177 0.208,0.208 10 false *b

Place paint marks on the chain sub-assembly, camshaft timing gear assembly and camshaft timing exhaust gear assembly.

Text in Illustration
*a Paint Mark
*b Timing Mark


b.
A337702

Remove the 2 bolts and timing chain cover plate from the timing chain or belt cover sub-assembly.


c.

Remove the gasket from the timing chain cover plate.


d.
A101303E24
2.292,0.813 2.604,0.313 2.604,0.313 2.698,0.313 true 1.771,1.552 1.938,1.896 1.938,1.896 2.063,1.896 true 0.563,1.833 0.563,1.51 false 2.719,0.229 2.917,0.448 0.198,0.219 10 false *a 2.104,1.802 2.333,1.99 0.229,0.188 10 false *b 0.51,1.854 0.74,2.042 0.229,0.188 10 false *c

Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.

Text in Illustration
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


e.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.


f.
A340033

Remove the bolt, nut, No. 1 chain tensioner assembly and gasket.


Hide 13512 16.REMOVE NO. 2 CAMSHAFT

a.
A337706

Uniformly loosen the 12 bolts and then remove the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps.

NOTICE:

Uniformly loosen the bolts while keeping the No. 2 camshaft level.



b.

Move the camshaft in the direction shown in the illustration to loosen the chain sub-assembly, and then remove the No. 2 camshaft.

A337707E01
2.595,0.361 2.811,0.572 0.216,0.211 10 *a 0.092,0.886 0.287,1.072 0.195,0.186 10 *c 0.391,0.362 0.587,0.553 0.195,0.191 10 *b 1.227,0.444 0.572,0.444 false 2.027,0.441 2.577,0.441 false 0.265,0.967 0.384,0.967 0.384,0.967 0.623,1.444 false

Text in Illustration
*a Camshaft *b No. 2 Camshaft
*c Chain Sub-assembly - -

NOTICE:

Do not pry the No. 2 camshaft with a tool as an excessive amount of force may be applied to it.



Hide 13511 17.REMOVE CAMSHAFT

a.
A337714

Uniformly loosen the 8 bolts and then remove the 4 No. 2 camshaft bearing caps.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



b.
A337708

Remove the camshaft while holding the chain sub-assembly.

NOTICE:

Do not pry the camshaft with a tool as an excessive amount of force may be applied to it.



c.
A337709

Secure the chain sub-assembly with a string as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover sub-assembly.



Hide 18.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Check the lock of the camshaft timing gear assembly.

i.
A346182E01
0.173,0.522 0.502,0.719 0.330,0.198 10 SST 2.082,0.957 2.253,1.150 0.171,0.193 10 *a 0.56,0.605 0.728,0.605 0.728,0.605 0.99,1.31 false 2.288,1.052 2.505,1.052 2.505,1.052 2.693,0.915 false

Using SST, grip the hexagonal portion, and then secure SST and camshaft in a vise as shown in the illustration and check that the camshaft timing gear assembly does not rotate.

SST
09212-31010  

Text in Illustration
*a Hexagonal Portion

NOTICE:
·

Do not damage the camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.





b.

Release the lock pin.

i.

Clean the camshaft journal with non-residue solvent.


ii.
A336435E04
1.906,1.375 0.479,0.854 0.479,0.854 1.521,1.448 true 0.865,3.792 0.99,3.792 0.99,3.792 1.406,3.625 true 1.396,3.406 0.896,3.406 true 2.073,3.76 2.625,3.76 true 2.615,3.448 2.51,3.448 2.51,3.448 2.052,3.271 true 1.531,1.594 2.281,2.167 2.281,2.167 1.896,1.656 true 2.656,3.667 2.844,3.875 0.188,0.208 10 false *d 0.688,3.313 0.885,3.51 0.198,0.198 10 false *d 0.667,3.677 0.885,3.885 0.219,0.208 10 false *c 2.646,3.344 2.854,3.542 0.208,0.198 10 false *c 2.323,2.125 2.521,2.344 0.198,0.219 10 false *b 0.281,0.74 0.479,0.958 0.198,0.219 10 false *a

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

Text in Illustration
*a Retard Side Path
*b Advance Side Path
*c Open
*d Close
V100144

Rubber Piece
V100145

Vinyl Tape

HINT:

1 retard side path and 1 advance side path are provided in the groove of the camshaft. Plug one of the paths with a rubber piece.



iii.

Break through the tape over the advance side path, and then break through the tape over the retard side path on the opposite side from the hole over the advance side path as shown in the illustration.


iv.
A336436E01
0.455,0.433 0.642,0.644 0.187,0.211 10 *a 2.653,0.477 2.859,0.705 0.206,0.228 10 *b 1.568,1.242 0.886,0.563 0.886,0.563 0.671,0.563 false 1.846,1.388 2.446,0.598 2.446,0.598 2.63,0.598 false

Apply compressed air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths accessible through the holes in the tape.

Text in Illustration
*a Retard Side Path
*b Advance Side Path

NOTICE:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.



v.
A336437E04
1.563,1.219 0.958,0.563 0.958,0.563 0.854,0.563 false 1.875,1.365 2.5,0.573 2.5,0.573 2.615,0.573 false 0.656,0.448 0.854,0.677 0.198,0.229 10 false *a 2.646,0.469 2.865,0.667 0.219,0.198 10 false *b 0.938,1.594 1.135,1.802 0.198,0.208 10 false *c 2.417,1.698 2.677,1.917 0.26,0.219 10 false *d

Check that the camshaft timing gear assembly revolves in the advance direction when reducing the air pressure applied to the retard side path.

OK:

Gear rotates in the advance direction.


Text in Illustration
*a Retard Side Path
*b Advance Side Path
*c Decompress
*d Hold Pressure

HINT:

This operation releases the lock pin which holds the timing gear in the most retarded position.



vi.

When the camshaft timing gear assembly reaches the most advanced position, release the air pressure from the retard side path and advance side path in that order.

NOTICE:
·

Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

·

When releasing the air pressure from the advance side path, release it slowly.





c.

Check for smooth rotation.

i.

Rotate the camshaft timing gear assembly within its movable range several times, but do not turn it to the most retarded position. Check that the gear rotates smoothly.

CAUTION:

Do not use air pressure to perform the smooth operation check.




d.

Check the lock in the most retarded position.

i.

Confirm that the camshaft timing gear assembly becomes locked at the most retarded position.



Hide 13050 19.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A344523E05
0.698,0.771 0.854,0.771 0.854,0.771 0.979,1.302 true 2.333,1.177 2.479,1.177 2.479,1.177 2.667,0.948 true 0.354,0.667 0.688,0.865 0.333,0.198 10 false SST 2.135,1.063 2.375,1.281 0.24,0.219 10 true *a

Using SST, grip the hexagonal portion, and then secure SST and camshaft in a vise as shown in the illustration.

SST
09212-31010  

Text in Illustration
*a Hexagonal Portion

NOTICE:
·

Do not damage the camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A336434E02
0.24,1.5 0.24,1.698 false 1.573,0.948 1.771,0.208 1.771,0.208 2.031,0.208 false 0.896,0.917 0.792,0.302 false 1.188,1.281 0.781,0.281 0.781,0.281 0.594,0.281 false 0.875,1.375 0.781,0.302 false 0.177,1.719 0.396,1.927 0.219,0.208 10 false *1 2.083,0.115 2.323,0.313 0.24,0.198 10 false *a 0.406,0.177 0.635,0.396 0.229,0.219 10 false *b

Remove the flange bolt and camshaft timing gear assembly.

Text in Illustration
*1 Flange Bolt
*a Straight Pin
*b Do Not Remove

NOTICE:
·

Be sure not to remove the other 3 bolts.

·

If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.




Hide 13070A 20.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Check the lock of the camshaft timing exhaust gear assembly.

i.
A346182E01
0.173,0.522 0.502,0.719 0.330,0.198 10 SST 2.082,0.957 2.253,1.150 0.171,0.193 10 *a 0.56,0.605 0.728,0.605 0.728,0.605 0.99,1.31 false 2.288,1.052 2.505,1.052 2.505,1.052 2.693,0.915 false

Using SST, grip the hexagonal portion, and then secure SST and No. 2 camshaft in a vise as shown in the illustration and check that the camshaft timing exhaust gear assembly does not rotate.

SST
09212-31010  

Text in Illustration
*a Hexagonal Portion

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.





b.
A336443E04
1.531,1.406 0.708,1.542 0.708,1.542 1.917,1.49 true 1.51,1.698 2.604,1.885 2.604,1.885 1.896,1.615 true 0.802,3.385 1.021,3.385 1.021,3.385 1.448,3.302 true 0.781,3.802 1.01,3.802 1.01,3.802 1.427,3.708 true 2.021,3.406 2.594,3.406 true 2.573,3.792 2.323,3.792 2.323,3.792 2,3.604 true 2.635,1.802 2.854,2 0.219,0.198 10 false *a 0.49,1.438 0.708,1.635 0.219,0.198 10 false *b 0.594,3.271 0.792,3.469 0.198,0.198 10 false *c 0.583,3.708 0.802,3.906 0.219,0.198 10 false *d 2.594,3.688 2.813,3.885 0.219,0.198 10 false *c 2.615,3.313 2.833,3.51 0.219,0.198 10 false *d

Release the lock pin.

i.

Clean the No. 2 camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

Text in Illustration
*a Retard Side Path
*b Advance Side Path
*c Open
*d Close
V100144

Rubber Piece
V100145

Vinyl Tape

HINT:

There are 4 oil paths in the grooves of the No. 2 camshaft. Plug 2 paths with pieces of rubber.



iii.

Break through the tape over the advance side path, and then break through the tape over the retard side path on the opposite side from the hole over the advance side path as shown in the illustration.


iv.
A336444E01
0.45,0.521 0.637,0.732 0.187,0.211 10 *a 2.681,0.268 2.887,0.495 0.206,0.228 10 *b 1.559,1.331 0.877,0.652 0.877,0.652 0.662,0.652 false 1.877,1.178 2.477,0.387 2.477,0.387 2.662,0.387 false

Apply compressed air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths (the advance side path and retard side path).

Text in Illustration
*a Retard Side Path
*b Advance Side Path

NOTICE:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.


HINT:

The lock pin is released in this condition.



v.
A336445E04
1.542,1.333 0.938,0.667 0.938,0.667 0.833,0.667 true 1.875,1.177 2.5,0.385 2.5,0.385 2.615,0.385 true 0.625,0.563 0.833,0.792 0.208,0.229 10 false *a 2.646,0.302 2.865,0.531 0.219,0.229 10 false *b 2.417,1.5 2.594,1.698 0.177,0.198 10 false *c 0.958,1.688 1.198,1.885 0.24,0.198 10 false *d

Check that the camshaft timing exhaust gear assembly turns in the retard direction when reducing the air pressure applied to the advance side path.

Text in Illustration
*a Retard Side Path
*b Advance Side Path
*c Decompress
*d Hold Pressure

HINT:

The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.



vi.

When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.




c.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (21.5 to 23.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.

NOTICE:

When the air pressure is released from the advance side path and then from the retard side path, the gear automatically returns to the most advanced position due to the advance assist spring operation, and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




d.

Check the lock at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



Hide 13070A 21.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A344523E05
0.698,0.771 0.854,0.771 0.854,0.771 0.979,1.302 true 2.333,1.177 2.479,1.177 2.479,1.177 2.667,0.948 true 0.354,0.667 0.688,0.865 0.333,0.198 10 false SST 2.135,1.063 2.375,1.281 0.24,0.219 10 true *a

Using SST, grip the hexagonal portion, and then secure SST and No. 2 camshaft in a vise as shown in the illustration.

SST
09212-31010  

Text in Illustration
*a Hexagonal Portion

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A336439E04
0.229,1.635 0.229,1.802 false 1.552,1.073 1.688,0.417 1.688,0.417 1.813,0.417 false 0.833,1.583 0.948,1.885 0.948,1.885 1.052,1.573 true 0.771,1.125 0.542,0.698 0.542,0.698 1.01,1.208 true 0.354,0.563 0.542,0.76 0.188,0.198 10 false *b 1.844,0.323 2.042,0.521 0.198,0.198 10 false *a 0.156,1.823 0.365,2.021 0.208,0.198 10 false *1 0.885,1.906 1.094,2.125 0.208,0.219 10 false *b

Remove the flange bolt and camshaft timing exhaust gear assembly.

Text in Illustration
*1 Flange Bolt
*a Straight Pin
*b Do Not Remove

NOTICE:

Be sure not to remove the other 4 bolts.