Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.

Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When either of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM according to the engine speed and throttle valve position. The ECM continues operating in fail-safe mode until a pass condition is detected.


A170707E04
1.354,0.125 1.615,1.552 false 2.156,1.063 1.792,1.521 false 4.438,1.292 3.792,2.229 false 4.885,0.875 4.542,0.083 false 4.542,0.083 4.302,0.083 false 0.042,0 1.354,0.417 1.313,0.417 10 false Temperature Sensor (Thermistor) 1.896,0.177 2.177,0.396 0.281,0.219 10 false +B 1.875,0.5 3.24,0.74 1.365,0.24 10 false Power Transistor 2.219,0.969 3.99,1.167 1.771,0.198 10 false Platinum Hot Wire (Heater) 1.302,1.552 1.469,1.76 0.167,0.208 10 false A 2.104,1.552 2.292,1.75 0.188,0.198 10 false B 2.625,1.677 3.635,1.875 1.01,0.198 10 false Output Voltage 2.563,0 4.365,0.198 1.802,0.198 10 false Platinum Hot Wire (Heater) 2.99,2.26 5.104,2.469 2.115,0.208 10 false Temperature Sensor (Thermistor)

DTC No. DTC Detection Condition Trouble Area
P0102 Mass air flow meter sub-assembly voltage is below 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


P0103 Mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM



HINT:

When either of these DTCs is stored, check the air flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

MAF (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter sub-assembly power source circuit

·

Open or short in VG circuit


160.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter sub-assembly or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly and stores a DTC.

Example:

When the sensor output voltage remains below 0.2 V, or higher than 4.9 V for more than 3 seconds, the ECM stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0102, P0103.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A355925E04
5.802,1.094 6.344,1.302 0.542,0.208 10 false VG 5.75,1.583 6.146,1.75 0.396,0.167 10 false E2G 5.771,2.885 6.198,3.094 0.427,0.208 10 false MREL 5.333,1.198 5.698,1.354 0.365,0.156 10 false C154 5.344,1.698 5.708,1.854 0.365,0.156 10 false C154 5.365,2.979 5.74,3.229 0.375,0.25 10 false G181 5.552,2.792 5.75,3.021 0.198,0.229 10 false 6 5.51,1.521 5.833,1.698 0.323,0.177 10 false 32 5.51,1.01 5.74,1.219 0.229,0.208 10 false 24 5.104,1.104 5.229,1.333 0.125,0.229 10 false 3 5.094,1.615 5.25,1.823 0.156,0.208 10 false 2 4.781,1.115 5.052,1.344 0.271,0.229 10 false VG 4.719,1.615 5.063,1.781 0.344,0.167 10 false E2G 3.865,0.792 4.083,0.979 0.219,0.188 10 false +B 3.688,0.792 3.865,1.01 0.177,0.219 10 false 1 3.052,1.042 3.698,1.188 0.646,0.146 10 false EFI NO. 2 3.802,2.271 5.135,2.698 1.333,0.427 10 false Mass Air Flow Meter Sub-assembly 3.802,2.104 4.146,2.26 0.344,0.156 10 false C33 2.51,0.885 2.833,1.042 0.323,0.156 10 false 1B 2.51,1.229 2.833,1.385 0.323,0.156 10 false 1B 2.635,0.698 2.885,0.854 0.25,0.156 10 false 4 2.625,1.052 2.865,1.208 0.24,0.156 10 false 2 1.875,1.583 2.198,1.76 0.323,0.177 10 false EFI 1.208,1.031 1.438,1.188 0.229,0.156 10 false EFI 1.354,1.667 1.573,1.813 0.219,0.146 10 false 1B 1.177,1.656 1.323,1.823 0.146,0.167 10 false 3 0.74,0.885 0.99,1.063 0.25,0.177 10 false 1C 0.719,0.688 0.875,0.865 0.156,0.177 10 false 1 1.542,1.906 2.781,2.333 1.24,0.427 10 false NO.1 Integration Relay 0.458,2.646 0.99,2.865 0.531,0.219 10 false P/I-B 0.646,3.719 1.156,3.938 0.51,0.219 10 false Battery 6.115,3.469 6.802,3.708 0.688,0.24 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B



A

2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE VOLTAGE)
U147481E02
1.365,2.021 0.969,2.5 false 0.146,0.094 0.479,0.333 0.333,0.24 10 false *a 0.75,2.49 1,2.677 0.25,0.188 10 false +B 0.333,1.865 0.615,2.021 0.281,0.156 10 false C33

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C33-1 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter sub-assembly)



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-3 (VG) - C154-24 (VG) Always Below 1 Ω
C33-2 (E2G) - C154-32 (E2G) Always Below 1 Ω
C33-3 (VG) or C154-24 (VG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C154-32 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-2 (E2G) - C154-32 (E2G) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-1 (+B) - 1B-4 Always Below 1 Ω
C33-1 (+B) or 1B-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR