Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  P0430  Catalyst System Efficiency Below Threshold (Bank 2)  


DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the TWC, the ECM calculates the Oxygen Storage Capacity (OSC) of the TWC. This calculation is based on the voltage output of the heated oxygen sensor while performing active air-fuel ratio control.

The OSC value is an indication of the oxygen storage capacity of the TWC. When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If a rich-lean cycle of the heated oxygen sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the heated oxygen sensor and TWC.

The ECM uses the OSC value to determine the state of the TWC. If any deterioration has occurred, it illuminates the MIL and stores a DTC.

DTC No. DTC Detection Condition Trouble Area
P0420 Oxygen storage capacity value is smaller than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leakage from exhaust system

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Heated oxygen sensor (bank 1 sensor 2)

·

Exhaust manifold sub-assembly RH (TWC: Front Catalyst)

·

Front exhaust pipe assembly (TWC: Rear Catalyst)


P0430 Oxygen storage capacity value is smaller than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leakage from exhaust system

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Heated oxygen sensor (bank 2 sensor 2)

·

Exhaust manifold sub-assembly LH (TWC: Front Catalyst)

·

Front No. 2 exhaust pipe assembly (TWC: Rear Catalyst)



HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



CATALYST LOCATION

A223836E05
0.406,1.208 0.823,1.042 false 1.115,3.146 1.51,2.719 false 1.708,1.635 1.833,1.26 false 2.208,3.531 2.323,3.292 false 4.323,2.125 4.615,1.76 false 5.125,0.667 5.521,0.938 false 0.938,0.604 1.208,0.5 false 1.823,1.063 1.635,0.948 false 0.917,1.885 1.344,2.094 false 1.885,2.458 2.083,3.021 false 0.24,1.156 0.427,1.323 0.188,0.167 10 false *1 1.656,2.302 1.896,2.469 0.24,0.167 10 false *10 0.938,3.094 1.125,3.26 0.188,0.167 10 false *2 1.625,1.677 1.813,1.844 0.188,0.167 10 false *3 2.115,3.563 2.302,3.729 0.188,0.167 10 false *4 4.229,2.167 4.417,2.333 0.188,0.167 10 false *5 4.969,0.552 5.156,0.719 0.188,0.167 10 false *6 1.24,0.417 1.427,0.583 0.188,0.167 10 false *7 0.74,1.781 0.927,1.948 0.188,0.167 10 false *8 1.448,0.854 1.635,1.021 0.188,0.167 10 false *9

Text in Illustration
*1 Exhaust Manifold Sub-assembly RH (TWC: Front Catalyst) *2 Exhaust Manifold Sub-assembly LH (TWC: Front Catalyst)
*3 Front Exhaust Pipe (TWC: Rear Catalyst) *4 Front No. 2 Exhaust Pipe (TWC: Rear Catalyst)
*5 Center Exhaust Pipe Assembly *6 Tailpipe Assembly
*7 Air Fuel Ratio Sensor (for Bank 1 Sensor 1) *8 Air Fuel Ratio Sensor (for Bank 2 Sensor 1)
*9 Heated Oxygen Sensor (for Bank 1 Sensor 2) *10 Heated Oxygen Sensor (for Bank 2 Sensor 2)

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst monitor. This is very useful for verifying the completion of a repair.


A201252E31
0.676,0.378 1.594,0.545 0.918,0.168 10 Vehicle Speed 0.181,0.777 1.567,1.370 1.387,0.592 10 Between 64 km/h and 113 km/h (40 mph and 70 mph) 1.223,2.232 1.599,2.393 0.376,0.161 10 Idling 0.465,2.511 1.591,2.665 1.125,0.153 10 Engine Switch off 2.35,2.116 2.547,2.305 0.197,0.189 10 [A] 3.908,0.733 4.115,0.908 0.207,0.175 10 [B] 2.159,2.847 2.755,3.015 0.595,0.168 10 Warm up 3.364,2.871 4.599,3.017 1.235,0.146 10 10 minutes or more 5.712,2.718 6.051,2.863 0.339,0.145 10 Time 1.576,3.253 6.033,3.475 4.457,0.221 10 (HINT: Even if vehicle stops during driving pattern, test can be resumed) 4.977,0.423 5.593,0.584 0.616,0.161 10 NOTICE: 4.977,0.708 7.069,1.536 2.092,0.828 10 This test will not be completed if the vehicle is driven at an absolutely constant speed such as with the cruise control activated.

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) and turn the GTS on.

7.

Enter the following menus: Powertrain / Engine and ECT / Monitor.

8.

Check that Catalyst / Status2 is Incomplete.

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

10.

Drive the vehicle between 40 and 70 mph (64 and 113 km/h) for 10 minutes or more [B].

11.

The monitor items will change to Complete as the catalyst monitor operates.

12.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

13.

Check if any DTCs (pending DTCs) are stored.


HINT:

If Catalyst does not change to Complete, and no pending DTCs are stored, extend the driving time.


CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.

A118003E93
3.624,0.851 3.858,1.054 0.233,0.203 10 (c) 0.575,0.564 1.659,0.767 1.084,0.203 10 Engine Speed 0.841,0.978 1.614,1.181 0.773,0.203 10 3000 rpm 0.841,1.51 1.593,1.713 0.752,0.203 10 2000 rpm 1.112,2.468 1.562,2.671 0.450,0.203 10 Idling 0.325,2.691 1.452,2.902 1.127,0.211 10 Engine Switch off 1.644,2.601 1.877,2.804 0.234,0.203 10 (a) 2.07,2.381 2.304,2.584 0.234,0.203 10 (b) 4.787,0.851 5.021,1.054 0.234,0.203 10 (d) 5.101,1.401 5.335,1.603 0.234,0.203 10 (d) 2.094,3.065 3.011,3.268 0.917,0.203 10 Warming up 3.364,3.065 4.542,3.268 1.178,0.203 10 At least 3 minutes 5.293,3.208 6.110,3.411 0.817,0.203 10 2 seconds 4.863,3.317 5.333,3.531 0.471,0.214 10 Check 6.634,2.714 7.035,2.917 0.400,0.203 10 Time 6.55,3.122 7.026,3.36 0.476,0.238 4.902,3.074 4.902,3.295 false 4.902,3.295 5.259,3.295 false 5.196,3.074 5.2,3.295 false

(a) Connect the GTS to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS.



HINT:
·

If either of the voltage outputs of the air fuel ratio or heated oxygen sensor does not fluctuate, or either of the sensors makes a noise, the sensor may be malfunctioning.

·

If the voltage outputs of both of the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

·

If the Three-Way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the TWC) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).


A121610E45
0.07,0.068 4.752,0.287 4.682,0.219 12 Voltage output when active air-fuel ratio control not performed: 2.374,0.421 3.392,0.601 1.019,0.180 10 Normal Catalyst 4.744,0.426 6.089,0.574 1.345,0.148 10 Deteriorated Catalyst 0.257,2.118 1.115,2.640 0.858,0.522 10 Waveform of HO2 Sensor behind TWC 0.257,0.653 1.269,1.297 1.012,0.644 10 Waveform of A/F Sensor in front of TWC 1.446,0.789 1.823,0.937 0.378,0.148 10 3.5 V 1.446,1.123 1.845,1.266 0.399,0.143 10 3.0 V 1.446,2.104 1.793,2.253 0.347,0.150 10 1.0 V 1.446,2.774 1.736,2.922 0.290,0.148 10 0 V 2.64,3.111 3.396,3.257 0.755,0.146 10 10 seconds 5.042,3.08 5.796,3.221 0.755,0.141 10 10 seconds


CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for air fuel ratio sensor function provided in the Active Test. The Control the Injection Volume for air fuel ratio sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for air fuel ratio sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

On the GTS, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for air fuel ratio sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E50
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.469,1.604 1.917,1.792 0.448,0.188 8 false +12.5% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.135 6.885,6.563 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leakage from exhaust system (air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.417,3.677 1.865,3.865 0.448,0.188 8 false +12.5% 4.01,1.594 4.458,1.781 0.448,0.188 8 false +12.5% 4,3.667 4.448,3.854 0.448,0.188 8 false +12.5% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.406,5.75 1.854,5.938 0.448,0.188 8 false +12.5% 1.375,7.771 1.823,7.958 0.448,0.188 8 false +12.5% 4.031,7.792 4.479,7.979 0.448,0.188 8 false +12.5% 4.073,5.729 4.521,5.917 0.448,0.188 8 false +12.5% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for air fuel ratio sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, P0430 a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171, P0174 (System Too Lean) and P0172, P0175 (System Too Rich).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result
Result Proceed to
P0420 and/or P0430 A
P0420 and/or P0430 and other DTCs B

HINT:

If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


e.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


f.

Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V


Result
Status of
AFS Voltage B1S1
or
AFS Voltage B2S1
Status of
O2S B1S2
or
O2S B2S2
Air Fuel Ratio Condition and Air Fuel Ratio Sensor and Heated Oxygen Sensor Condition Misfire Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-Way Catalytic Converter (TWC)

·

Gas leakage from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leakage from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leakage from exhaust system


C
Lean Lean Actual air-fuel ratio lean May occur
·

Extremely rich or lean actual air-fuel ratio

·

Gas leakage from exhaust system


D
Rich Rich Actual air-fuel ratio rich -
·

Extremely rich or lean actual air-fuel ratio

·

Gas leakage from exhaust system


D

Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the AFS is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.



HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

3.INSPECT FOR EXHAUST GAS LEAK

B

C

4.INSPECT EXHAUST FOR GAS LEAK

D

CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO, REPLACE FAULTY AREA AND GO TO NEXT STEP

3.INSPECT FOR EXHAUST GAS LEAK
OK:

No gas leakage.


Result
Result Proceed to
NG A
OK B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).



A

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

B

5.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
4.INSPECT EXHAUST FOR GAS LEAK
OK:

No gas leakage.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).



OK

NG

REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT

5.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
a.

According to the DTCs output in the Check for Any Other DTCs Output step, proceed to the next step by referring to the table below.

Result
Result Proceed to
P0420 A
P0430 B
P0420 and P0430 A and B



A

6.REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST)

B

7.REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST)
6.REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST)
a.

Replace the exhaust manifold sub-assembly RH (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL).



NEXT

REPLACE EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

7.REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST)
a.

Replace the exhaust manifold sub-assembly LH (See page Engine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL).



NEXT

REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)