Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the engine switch is turned to on (IG), power is supplied to the MIL circuit and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the engine switch is first turned to on (IG), the MIL should be illuminated, and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

for Automatic Transmission

A182518E12
6.212,2.403 6.544,2.560 0.332,0.157 10 G56 6.212,2.587 6.664,2.743 0.452,0.156 10 ECM 6.03,0.999 6.337,1.155 0.306,0.156 10 W 5.764,1.203 5.957,1.359 0.193,0.156 10 21 4.926,1.113 5.152,1.268 0.226,0.156 10 G7 4.995,0.928 5.188,1.084 0.193,0.156 10 7 2.746,1.102 2.972,1.258 0.226,0.156 10 G6 2.734,0.91 2.927,1.066 0.193,0.156 10 28 3.709,1.28 4.005,1.442 0.296,0.163 10 MIL 4.508,1.231 4.846,1.393 0.338,0.163 10 CHK 3.033,1.231 3.329,1.393 0.296,0.163 10 IG+ 1.9,0.936 2.427,1.099 0.528,0.163 10 GAUGE 3.38,2.085 4.915,2.248 1.535,0.163 10 Combination Meter 0.466,1.097 1.442,1.267 0.977,0.170 10 from IG2 relay

for Manual Transmission

A182518E13
6.213,2.403 6.583,2.560 0.370,0.157 10 G55 6.213,2.587 6.665,2.743 0.452,0.156 10 ECM 6.03,0.999 6.337,1.155 0.306,0.156 10 W 5.764,1.203 5.957,1.359 0.193,0.156 10 13 4.926,1.113 5.152,1.268 0.226,0.156 10 G7 4.995,0.928 5.188,1.084 0.193,0.156 10 7 2.728,1.11 2.954,1.266 0.226,0.156 10 G6 2.734,0.91 2.927,1.066 0.193,0.156 10 28 3.709,1.28 4.005,1.442 0.296,0.163 10 MIL 4.508,1.231 4.846,1.393 0.338,0.163 10 CHK 3.033,1.231 3.329,1.393 0.296,0.163 10 IG+ 1.9,0.936 2.427,1.099 0.528,0.163 10 GAUGE 3.38,2.085 4.915,2.248 1.535,0.163 10 Combination Meter 0.466,1.097 1.442,1.267 0.977,0.170 10 from IG2 relay

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Check that the MIL is illuminated.

Result
Result Proceed to
MIL remains on A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Check for DTCs (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR). If DTCs are output, write them down.



e.

Check that the MIL turns off.

OK:

MIL turns off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



d.

Reconnect the ECM connector.



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
G7-7 (CHK) - G56-21 (W) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
G7-7 (CHK) - G55-13 (W) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
G7-7 (CHK) or G56-21 (W) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
G7-7 (CHK) or G55-13 (W) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the engine switch is turned to on (IG).

OK:

MIL is illuminated.




OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the engine switch on (IG).


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The GTS cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

Refer to the combination meter troubleshooting procedure (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>PROBLEM SYMPTOMS TABLE).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

REPLACE COMBINATION METER ASSEMBLY