Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2016.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM T

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Entire System
Symptom Suspected Area See page
Entire combination meter assembly does not operate Refer to "Entire Combination Meter does not Operate" (Click here)
Meter illumination is always dark Refer to "Meter Illumination is Always Dark" (Click here)
Meter illumination does not dim at night Refer to "Meter Illumination does not Dim at Night" (Click here)
Operating light control rheostat does not change light brightness Refer to "Operating Light Control Rheostat does not Change Light Brightness" (Click here)

Meter or Gauge
Symptom Suspected Area See page
Speedometer malfunction Refer to "Speedometer Malfunction" (Click here)
Tachometer malfunction Refer to "Tachometer Malfunction" (Click here)
Fuel receiver gauge malfunction Refer to "Fuel Receiver Gauge Display Malfunction" (Click here)
Engine coolant temperature malfunction Refer to "Engine Coolant Temperature Receiver Gauge Malfunction" (Click here)
ODO/TRIP meter malfunction Refer to "Odo/Trip Switch Malfunction" (Click here)

Warning Light or Indicator Light
Symptom Suspected Area See page
FRONT FOG indicator light does not come on*1 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Lighting system (Click here)
Combination meter assembly (Click here)
REAR FOG indicator light does not come on*2 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Lighting system (Click here)
Combination meter assembly (Click here)
BEAM indicator light does not come on CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Lighting system (Click here)
Combination meter assembly (Click here)
Turn signal indicator light malfunction Lighting system (Click here)
Harness or connector -
Turn signal flasher assembly (Click here)
Combination meter assembly (Click here)
FUEL warning light does not come on (Fuel receiver gauge operates normally) Check indicator/warning light (Click here)
Combination meter assembly (Click here)
Brake warning light does not come on Check indicator/warning light (Click here)
Harness or connector -
Master cylinder reservoir sub-assembly (brake fluid level warning switch) (Click here)
Proceed to "Brake Warning Light Come ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "Brake Warning Light Come ON" (for Vacuum Brake Booster, 2TR-FE) (Click here)
Proceed to "Brake Warning Light Come ON" (for Vacuum Brake Booster, 5L-E) (Click here)
Combination meter assembly (Click here)
Brake warning light does not go off Check indicator/warning light (Click here)
Harness or connector -
Master cylinder reservoir sub-assembly (brake fluid level warning switch) (Click here)
Proceed to "Brake Warning Light Remains ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "Brake Warning Light Remains ON" (for Vacuum Brake Booster, 2TR-FE) (Click here)
Proceed to "Brake Warning Light Remains ON" (for Vacuum Brake Booster, 5L-E) (Click here)
Combination meter assembly (Click here)
SRS warning light does not come on Check indicator/warning light (Click here)
Proceed to "SRS Warning Light does not Come ON" (Click here)
Combination meter assembly (Click here)
SRS warning light does not go off Check indicator/warning light (Click here)
Proceed to "SRS Warning Light does not Remains ON" (Click here)
Combination meter assembly (Click here)
DOOR warning light does not come on CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Proceed to "Door Courtesy Switch Circuit" (Click here)
Proceed to "Back Door Courtesy Switch Circuit" (Click here)
Main body ECU (Click here)
Combination meter assembly (Click here)
CHARGE warning light does not come on*3 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Charging system (for 1GD-FTV) (Click here)
Charging system (for 2TR-FE) (Click here)
Combination meter assembly (Click here)
CHARGE warning light does not come on*4 Check indicator/warning light (Click here)
Harness or connector -
Generator assembly (for 1GR-FE) (Click here)
Generator assembly (for 1KD-FTV) (Click here)
Generator assembly (for 5L-E) (Click here)
Combination meter assembly (Click here)
MIL (Malfunction Indicator Lamp) malfunction Proceed to "MIL Circuit" (for 1GR-FE) (Click here)
MIL Circuit (for 2TR-FE) (Click here)
Proceed to "MIL CircuitW (for 1KD-FTV) (Click here)
Proceed to "MIL Circuit" (for 1GD-FTV) (Click here)
Proceed to "MIL Circuit" (for 1GD-FTV, w/ Urea SCR System) (Click here)
Proceed to "MIL Circuit" (for 5L-E) (Click here)
Combination meter assembly (Click here)
Front seat belt warning light does not come on Check indicator/warning light (Click here)
Proceed to "Driver Side Seat Belt Warning Light does not Operate" (Click here)
Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction" (Click here)
ABS warning light does not come on Check indicator/warning light (Click here)
Proceed to "ABS Warning Light Come ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "ABS Warning Light Come ON" (for Vacuum Brake Booster, 2TR-FE) (Click here)
Proceed to "ABS Warning Light Come ON" (for Vacuum Brake Booster, 5L-E) (Click here)
Combination meter assembly (Click here)
ABS warning light does not go off Check indicator/warning light (Click here)
Proceed to "ABS Warning Light Remains ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "ABS Warning Light Remains ON" (for Vacuum Brake Booster, 2TR-FE) (Click here)
Proceed to "ABS Warning Light Remains ON" (for Vacuum Brake Booster, 5L-E) (Click here)
Combination meter assembly (Click here)
PPS warning light malfunction*5 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Power steering system (Click here)
Combination meter assembly (Click here)
SLIP indicator light does not come on*6 Check indicator/warning light (Click here)
Proceed to "Slip Indicator Light Come ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "Slip Indicator Light Come ON" (for Vacuum Brake Booster, 2TR-FE) (Click here)
Combination meter assembly (Click here)
SLIP indicator light does not go off*6 Check indicator/warning light (Click here)
Proceed to "Slip Indicator Light Remains ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "Slip Indicator Light Remains ON" (for Vacuum Brake Booster) (Click here)
Combination meter assembly (Click here)
Cruise indicator light does not come on*7 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Proceed to "Cruise Main Indicator Light Circuit" (Click here)
Combination meter assembly (Click here)
Cruise set indicator light does not come on*7 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Proceed to "Cruise SET Indicator Light Circuit" (Click here)
Proceed to "Cruise SET Indicator Light Circuit" (w/ Dynamic Radar Cruise Control System) (Click here)
Combination meter assembly (Click here)
Radar cruise indicator light does not come on*8 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Proceed to "Cruise Main Indicator Light Circuit" (Click here)
Combination meter assembly (Click here)
Master warning light does not come on Check indicator/warning light (Click here)
Combination meter assembly (Click here)
A/T shift indicator light does not come on*9 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Automatic transmission system (for A750F, 1KD-FTV) (Click here)
Automatic transmission system (for AC60F, 1GR-FE) (Click here)
Automatic transmission system (for AC60F, 2TR-FE) (Click here)
Automatic transmission system (for AC60F, 1GD-FTV) (Click here)
Combination meter assembly (Click here)
SIL indicator light (UP, DOWN) does not come on*10, *11 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
ECD system (for 1KD-FTV) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
Center differential lock indicator light malfunction CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Differential system (Click here)
Combination meter assembly (Click here)
Rear differential lock indicator light malfunction*12 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Differential system (Click here)
Combination meter assembly (Click here)
4LO indicator light malfunction CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Differential system (Click here)
Combination meter assembly (Click here)
2nd START indicator light malfunction*9 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and start system) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Automatic transmission system (for A750F, 1KD-FTV) (Click here)
Automatic transmission system (for AC60F, 1GR-FE) (Click here)
Automatic transmission system (for AC60F, 2TR-FE) (Click here)
Automatic transmission system (for AC60F, 1GD-FTV) (Click here)
Combination meter assembly (Click here)
A/T OIL TEMP indicator light malfunction*9, *22 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Automatic transmission system (for A750F, 1KD-FTV) (Click here)
Automatic transmission system (for AC60F, 1GR-FE) (Click here)
Automatic transmission system (for AC60F, 2TR-FE) (Click here)
Automatic transmission system (for AC60F, 1GD-FTV) (Click here)
Combination meter assembly (Click here)
TAIL indicator light does not come on CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Main body ECU (Click here)
Combination meter assembly (Click here)
VSC OFF indicator light does not come on*6 Check indicator/warning light (Click here)
Proceed to "VSC OFF Indicator Light Come ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "VSC OFF Indicator Light Come ON" (for Vacuum Brake Booster) (Click here)
Combination meter assembly (Click here)
VSC OFF indicator light does not go off*6 Check indicator/warning light (Click here)
Proceed to "VSC OFF Indicator Light Remains ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "VSC OFF Indicator Light Remains ON" (for Vacuum Brake Booster) (Click here)
Combination meter assembly (Click here)
TRC OFF indicator light does not come on*6 Check indicator/warning light (Click here)
Proceed to "TRC OFF Indicator Light Come ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "TRC OFF Indicator Light Come ON" (for Vacuum Brake Booster) (Click here)
Combination meter assembly (Click here)
TRC OFF indicator light does not go off*6 Check indicator/warning light (Click here)
Proceed to "TRC OFF Indicator Light Remains ON" (for Hydraulic Brake Booster) (Click here)
Proceed to "TRC OFF Indicator Light Remains ON" (for Vacuum Brake Booster, 2TR-FE) (Click here)
Combination meter assembly (Click here)
Eco driving indicator light malfunction*9 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
SFI system (for 1GR-FE) (Click here)
SFI system (for 2TR-FE) (Click here)
ECD system (for 1KD-FTV) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
SPEED LIMITER indicator light malfunction*13 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
SFI system (for 1GR-FE) (Click here)
SFI system (for 2TR-FE) (Click here)
ECD system (for 1KD-FTV) (Click here)
ECD system (for 5L-E) (Click here)
Combination meter assembly (Click here)
T-BELT warning indicator light malfunction*14, *22 Check indicator/warning light (Click here)
Combination meter assembly (Click here)
GLOW indicator light malfunction *15 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
ECD system (for 1KD-FTV) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
GLOW indicator light malfunction*16 Harness or connector -
Combination meter assembly (Click here)
ECM (Click here)
CRAWL indicator light does not come on*17 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
CRAWL indicator light does not go off*17 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
Downhill assist control indicator light does not come on*18 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
Downhill assist control indicator light does not go off*18 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
Multi-terrain select indicator light does not come on*17 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
Multi-terrain select indicator light does not go off*17 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
Clearance sonar indicator light malfunction*19, *20 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
TOYOTA Parking Assist-sensor System (w/ Multi-display) (Click here)
TOYOTA Parking Assist-sensor System (w/o Multi-display) (Click here)
Combination meter assembly (Click here)
PCS warning light malfunction*21 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Pre-crash safety system (Click here)
Combination meter assembly (Click here)
Oil pressure warning light does not come on*22 Check indicator/warning light (Click here)
Engine oil pressure switch assembly (for 1GR-FE) (Click here)
Engine oil pressure switch assembly (for 2TR-FE) (Click here)
Engine oil pressure switch assembly (for 1KD-FTV) (Click here)
Engine oil pressure switch assembly (for 5L-E) (Click here)
Engine oil pressure switch assembly (for 1GD-FTV) (Click here)
Harness or connector -
Combination meter assembly (Click here)
Oil level warning light does not come on*22, *23, *24 Check indicator/warning light (Click here)
Engine oil level sensor (1GR-FE) (Click here)
Engine oil level sensor (for 1KD-FTV) (Click here)
Engine oil level sensor (for 1GD-FTV) (Click here)
Harness or connector -
Combination meter assembly (Click here)
Oil maintenance warning light does not come on*22, *25 Check indicator/warning light (Click here)
Combination meter assembly (Click here)
Kinetic dynamic suspension indicator light malfunction*26 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Kinetic dynamic suspension control System (Click here)
Combination meter assembly (Click here)
SEDIMENT/FILTER warning light does not come on*27 Check indicator/warning light (Click here)
Sediment warning switch (for 1KD-FTV) (Click here)
Combination meter assembly (Click here)
SEDIMENT warning light does not come on*28 Check indicator/warning light (Click here)
Sediment switch (for 5L-E) (Click here)
Combination meter assembly (Click here)
Key indicator light does not come on*22, *29 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Entry and start system (Click here)
Combination meter assembly (Click here)
BSM indicator light does not come on*30 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Blind spot monitor system (Click here)
Combination meter assembly (Click here)
Headlight beam level control system warning light does not come on*31 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Lighting system (Click here)
Combination meter assembly (Click here)
LED headlight warning light does not come on*31 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Check indicator/warning light (Click here)
Lighting system (Click here)
Combination meter assembly (Click here)
Tire pressure warning light does not come on*32 Check indicator/warning light (Click here)
Proceed to "Tire Pressure Warning Light Circuit" (Click here)
Combination meter assembly (Click here)
Washer level warning light does not come on*22, *33 Level warning switch assembly (Click here)
Harness or connector -
Combination meter assembly (Click here)
Diesel particulate filter warning light does not come on*34 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
Reductant warning indicator does not come on*35 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)

*1: w/ Front Fog Light

*2: w/ Rear Fog Light

*3: for 1GD-FTV, 2TR-FE

*4: for 1KD-FTV, 1GR-FE, 5L-E

*5: w/ Power Steering System

*6: w/ VSC

*7: w/ Cruise Control System

*8: w/ Dynamic Radar Cruise Control System

*9: for Automatic Transmission

*10: for Manual Transmission

*11: for Europe

*12 w/ Rear Differential Lock

*13: for Middle East

*14: for 1KD-FTV, 5L-E

*15: for 1KD-FTV, 1GD-FTV

*16: for 5L-E

*17: w/ CRAWL Control

*18: w/ Downhill Assist Control

*19: w/ TOYOTA Parking Assist-sensor System

*20: for Optitron Meter

*21: w/ Pre-crash Safety System

*22: for Analog Meter, Segment Display Type

*23: for 1KD-FTV, 1GD-FTV

*24: for 1GR-FE, Europe

*25: for 1KD-FTV, Europe

*26: w/ Kinetic Dynamic Suspension System

*27: w/ SEDIMENT/FILTER Warning Light

*28: w/ SEDIMENT Warning Light

*29: w/ Entry and Start System

*30: w/ Blind Spot Monitor System

*31: for LED Headlight

*32: w/ Tire Pressure Monitor System

*33: w/ Washer Fluid Level Warning System

*34: w/ DPF

*35: w/ Urea SCR System


Cruise Information Display (except Analog Meter, Segment Display Type)
Symptom Suspected Area See page
Average vehicle speed display malfunction (Combination meter assembly operates normally) Combination meter assembly (Click here)
Driving range display malfunction (Combination meter assembly operates normally) Combination meter assembly (Click here)
Average fuel consumption display display malfunction (Combination meter assembly operates normally) Combination meter assembly (Click here)
Average fuel consumption after refueling display malfunction (Combination meter assembly operates normally)* Combination meter assembly (Click here)
Current fuel consumption display malfunction (Combination meter assembly operates normally) Combination meter assembly (Click here)
Operating multi-information switch does not change multi-information display* Multi-information switch (steering pad switch assembly) (Click here)
Harness or connector -
LIN communication system (Click here)
Driving support switch control ECU (Click here)
Combination meter assembly (Click here)
Eco driving indicator zone display malfunction (for Automatic Transmission) Combination meter assembly (Eco driving indicator zone display setting) (Click here)
SFI system (for 1GR-FE) (Click here)
SFI system (for 2TR-FE) (Click here)
ECD system (for 1KD-FTV) (Click here)
Combination meter assembly (Click here)
Outside temperature display malfunction Air conditioning system (for Automatic Air Conditioning System) (Click here)
Air conditioning system (for Manual Air Conditioning System) (Click here)
Combination meter assembly (Click here)
Road surface ice display malfunction (outside temperature display operates normally) (for Optitron Meter) Combination meter assembly (Click here)
Digital speedometer display malfunction (speedometer operates normally)* Combination meter assembly (Click here)

*: for Optitron Meter


Multi-information Display (for Optitron Meter)
Symptom Suspected Area See page
Multi-information display does not light up (combination meter operates normally) Check indicator/warning light (Click here)
Combination meter assembly (Click here)
Multi-information display malfunction (all warning displays come on, cruise information display does not come on and outside temperature display indicates "F") CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Combination meter assembly (Click here)
Air suspension indicator display malfunction*1 CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Air suspension system (Click here)
Combination meter assembly (Click here)
Steering angle display malfunction CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Spiral cable sub-assembly (Click here)
Combination meter assembly (Click here)
Door open message is displayed when it should not be, not displayed when it should be, or not displayed correctly Proceed to "Door Courtesy Switch Circuit" (Click here)
Proceed to "Back Door Courtesy Switch Circuit" (Click here)
Main body ECU (Click here)
Combination meter assembly (Click here)
"MOON ROOF OPENED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*2 Sliding roof control system (Click here)
Combination meter assembly (Click here)
"ENGINE OIL PRESSURE LOW" message is displayed when it should not be, not displayed when it should be, or not displayed correctly Engine oil pressure switch assembly (for 1GR-FE) (Click here)
Engine oil pressure switch assembly (for 2TR-FE) (Click here)
Engine oil pressure switch assembly (for 1KD-FTV) (Click here)
Engine oil pressure switch assembly (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"RELEASE PARKING BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Brake warning light operate normally) Combination meter assembly (Click here)
"HIGH TRANSMISSION FLUID TEMPERATURE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*3 Automatic transmission system (for A750F, 1KD-FTV) (Click here)
Automatic transmission system (for AC60F, 1GR-FE) (Click here)
Automatic transmission system (for AC60F, 2TR-FE) (Click here)
Automatic transmission system (for AC60F, 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"CHECK TRANSMISSION SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*3 Automatic transmission system (for A750F, 1KD-FTV) (Click here)
Automatic transmission system (for AC60F, 1GR-FE) (Click here)
Automatic transmission system (for AC60F, 2TR-FE) (Click here)
Automatic transmission system (for AC60F, 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"SHIFT TO P POSITION" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*3, *4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"KEY NOT DETECTED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"KEY BATTERY LOW" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"CHECK CLUTCH SWITCH" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*5 Clutch pedal switch (Click here)
Combination meter assembly (Click here)
"CHECK STEERING LOCK SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4 Steering lock system (Click here)
Combination meter assembly (Click here)
"STEERING LOCK ACTIVE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4 Steering lock system (Click here)
Combination meter assembly (Click here)
"KEY DETECTED IN VEHICLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"AUTO POWER OFF TO CONSERVE BATTERY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"DEPRESS BRAKE PEDAL, TOUCH ENGINE SWITCH WITH KEY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*3, *4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"DEPRESS CLUTCH PEDAL, TOUCH ENGINE SWITCH WITH KEY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4, *5 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"DEPRESS BRAKE PEDAL AND PUSH ENGINE SWITCH TO START" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*3, *4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"DEPRESS CLUTCH PEDAL AND PUSH ENGINE SWITCH TO START" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4, *5 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"SHIFT TO P POSITION TO START" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*3 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"TURN POWER OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"SHIFT TO P POSITION AND PUSH ENGINE SWITCH TO TURN POWER OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*4 Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
Dynamic radar cruise control system message is displayed when it should not be, not displayed when it should be, or not displayed correctly*6 Dynamic radar cruise control system (Click here)
Combination meter assembly (Click here)
"ADJUSTING FRONT RADAR BEAM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*6 Dynamic radar cruise control system (Click here)
Combination meter assembly (Click here)
"CHECKING CRUISE CONTROL C/D" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*6 Dynamic radar cruise control system (Click here)
Combination meter assembly (Click here)
"CHECKING CRUISE CONTROL BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*6 Dynamic radar cruise control system (Click here)
Combination meter assembly (Click here)
"CLEAN RADAR SENSOR" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*6 Dynamic radar cruise control system (Click here)
Combination meter assembly (Click here)
"CRUISE CONTROL NOT AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*6 Dynamic radar cruise control system (Click here)
Combination meter assembly (Click here)
"CHECK CRUISE CONTROL SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*7 Cruise control system (Click here)
Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) (Click here)
Combination meter assembly (Click here)
Pre-crash safety system message is displayed when it should not be, not displayed when it should be, or not displayed correctly*8 Pre-crash safety system (Click here)
Combination meter assembly (Click here)
"BRAKE !" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*8 Pre-crash safety system (Click here)
Combination meter assembly (Click here)
"CHECK PCS SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*8 Pre-crash safety system (Click here)
Combination meter assembly (Click here)
"PCS TEMPORARILY NOT AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*8 Pre-crash safety system (Click here)
Combination meter assembly (Click here)
"CHECK AIR SUSPENSION SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 Suspension control system (Click here)
Combination meter assembly (Click here)
"AIR SUSPENSION TEST MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*1 Air suspension system (Click here)
Combination meter assembly (Click here)
TOYOTA parking assist-sensor system message is displayed when it should not be, not displayed when it should be, or not displayed correctly*9 TOYOTA Parking Assist-sensor System (w/ Multi-display) (Click here)
TOYOTA Parking Assist-sensor System (w/o Multi-display) (Click here)
Combination meter assembly (Click here)
"CHECK SONAR SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*9 TOYOTA Parking Assist-sensor System (w/ Multi-display) (Click here)
TOYOTA Parking Assist-sensor System (w/o Multi-display) (Click here)
Combination meter assembly (Click here)
"CLEAN SONAR" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*9 TOYOTA Parking Assist-sensor System (w/ Multi-display) (Click here)
TOYOTA Parking Assist-sensor System (w/o Multi-display) (Click here)
Combination meter assembly (Click here)
"BSM NOT AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*10 Blind spot monitor system (Click here)
Combination meter assembly (Click here)
"CHECK BSM SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*10 Blind spot monitor system (Click here)
Combination meter assembly (Click here)
"ENGINE OIL LOW" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12, *13 Engine oil level sensor (for 1GR-FE) (Click here)
Engine oil level sensor (for 1KD-FTV) (Click here)
Engine oil level sensor (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"FUEL FILTER MAINTENANCE REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12 Fuel filter assembly (sedimenter switch) (for 1KD-FTV) (Click here)
Fuel filter assembly (sedimenter switch) (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"DRAIN WATER FROM FUEL FILTER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12 Level warning switch (for 1KD-FTV) (Click here)
Level warning switch (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"CRAWL HAS BEEN DEACTIVATED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"CRAWL NOT AVAILABLE SELECT L4 AND SHIFT TO D OR R POSITION" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"CRAWL NOT AVAILABLE CHECK SYSTEM OPERATION CONDITIONS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"CHECK FUEL SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12 Fuel system (for 1KD-FTV) (Click here)
Fuel system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"T-BELT MAINTENANCE REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11 Combination meter assembly (Click here)
T-BELT maintenance reset message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11 Combination meter assembly (Click here)
T-BELT maintenance reset complete message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11 Combination meter assembly (Click here)
T-BELT maintenance mileage message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11 Combination meter assembly (Click here)
"OIL MAINTENANCE REQUIRED SOON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12, *15 Fuel system (for 1KD-FTV) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"OIL MAINTENANCE REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12, *15 ECD system (for 1KD-FTV) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
Oil maintenance required reset message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12, *15 ECD system (for 1KD-FTV) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
Oil maintenance reset complete message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12, *15 ECD system (for 1KD-FTV) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
Oil maintenance reset unfinished message is displayed when it should not be, not displayed when it should be, or not displayed correctly*11, *12, *15 ECD system (for 1KD-FTV) (Click here)
ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
Multi-terrain select message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"SHIFT TO L4" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"STOP THE VEHICLE AND SHIFT THE AUTOMATIC TRANSMISSION TO N" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"MULTI-TERRAIN SELECT NOT AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"OPERATION NOT POSSIBLE WHEN MULTI-TERRAIN SELECT ACTIVATED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"OPERATION NOT POSSIBLE WHEN CRAWL CONTROL ACTIVATED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"MULTI-TERRAIN SELECT HAS BEEN CANCELLED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*14 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Combination meter assembly (Click here)
"CHECK HEADLIGHT SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*16 Lighting system (Click here)
Combination meter assembly (Click here)
"LOW WASHER FLUID" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*17 Level warning switch assembly (Click here)
Combination meter assembly (Click here)
Clinometer display malfunction CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Yaw rate sensor (Click here)
Combination meter assembly (Click here)
Traction operation display malfunction CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Vehicle stability control system (for Vacuum Brake Booster) (Click here)
Combination meter assembly (Click here)
Center differential lock display malfunction CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Transfer system (Click here)
Combination meter assembly (Click here)
Rear differential lock display malfunction CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Transfer system (Click here)
Combination meter assembly (Click here)
Turn-by-turn navigation display malfunction*18 Navigation system (for Radio and Display Type) (Click here)
Navigation system (for Navigation Receiver Type) (Click here)
Combination meter assembly (Click here)
Compass display malfunction*18 Navigation system (for Radio and Display Type) (Click here)
Navigation system (for Navigation Receiver Type) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW FILL UP AdBlue IN **** km SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW FILL UP AdBlue IN **** MILES SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW FILL UP AdBlue IN **** km SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW FILL UP AdBlue IN **** MILES SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW NO START IN **** km! FILL UP AdBlue SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW NO START IN **** MILES! FILL UP AdBlue SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue EMPTY UNABLE TO RESTART ENGINE FILL UP AdBlue SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"EMISSIONS TOO HIGH CHECK AdBlue VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"EMISSIONS TOO HIGH NO START IN **** km! CHECK AdBlue VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"EMISSIONS TOO HIGH NO START IN **** MILES! CHECK AdBlue VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"EMISSIONS TOO HIGH UNABLE TO RESTART ENGINE CHECK AdBlue VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*19 ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"DPF FULL SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*20 ECD system (for 1KD-FTV) (Click here)
ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (1GD-FTV) (Click here)
Combination meter assembly (Click here)
"DPF FULL VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*20 ECD system (for 1KD-FTV) (Click here)
ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (1GD-FTV, w/o Urea SCR System) (Click here)
Combination meter assembly (Click here)
"MANUAL REGENERATION IN PROCESS KEEP FLAMMABLES AWAY FROM VEHICLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*20 ECD system (for 1KD-FTV) (Click here)
ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (1GD-FTV, w/o Urea SCR System) (Click here)
Combination meter assembly (Click here)
"DPF REGENERATION IN PROCESS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*20 ECD system (for 1KD-FTV) (Click here)
ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (1GD-FTV) (Click here)
Combination meter assembly (Click here)
"DPF MANUAL REGENERATION AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*20 ECD system (for 1KD-FTV) (Click here)
ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (1GD-FTV) (Click here)
Combination meter assembly (Click here)
"DPF FULL MANUAL REGENERATION REQUIRED SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly*20 ECD system (for 1KD-FTV, w/ DPF) (Click here)
ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
ECD system (1GD-FTV) (Click here)
Combination meter assembly (Click here)

*1: w/ Air Suspension System

*2: w/ Sliding Roof System

*3: for Automatic Transmission

*4: w/ Entry and Start System

*5: for Manual Transmission

*6: w/ Dynamic Radar Cruise Control System

*7: w/ Cruise Control System

*8: w/ Pre-crash Safety System

*9: w/ TOYOTA Parking Assist-sensor System

*10: w/ Blind Spot Monitor System

*11: for 1KD-FTV

*12: for 1GD-FTV

*13: for 1GR-FE, Europe

*14: w/ CRAWL Control

*15: for Europe

*16: for LED Headlight

*17: w/ Washer Fluid Level Warning System

*18: w/ Navigation System

*19: w/ Urea SCR System

*20: w/ DPF


Multi-information Display (for Analog Meter, Dot Display Type)
Symptom Suspected Area See page
Multi-information display does not light up (combination meter operates normally) Check indicator/warning light (Click here)
Combination meter assembly (Click here)
Multi-information display malfunction (all warning displays come on, cruise information display does not come on and outside temperature display indicates "F") CAN communication system (for LHD with Entry and Start System) (Click here)
CAN communication system (for LHD without Entry and Start System) (Click here)
CAN communication system (for RHD with Entry and Start System) (Click here)
CAN communication system (for RHD without Entry and Start System) (Click here)
Combination meter assembly (Click here)
"ENGINE OIL PRESSURE LOW" message is displayed when it should not be, not displayed when it should be, or not displayed correctly Engine oil pressure switch assembly (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"RELEASE PARKING BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Brake warning light operate normally) Combination meter assembly (Click here)
"HIGH TRANSMISSION FLUID TEMPERATURE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission) Automatic transmission system (for AC60F, 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"CHECK TRANSMISSION SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission) Automatic transmission system (for AC60F, 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"KEY NOT DETECTED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"DEPRESS BRAKE PEDAL, TOUCH ENGINE SWITCH WITH KEY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Automatic Transmission) Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"DEPRESS CLUTCH PEDAL, TOUCH ENGINE SWITCH WITH KEY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for Manual Transmission) Entry and start system (for Entry and Start System) (Click here)
Entry and start system (for Start Function) (Click here)
Combination meter assembly (Click here)
"ENGINE OIL LOW" message is displayed when it should not be, not displayed when it should be, or not displayed correctly Engine oil level sensor (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"FUEL FILTER MAINTENANCE REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly Fuel filter assembly (sedimenter switch) (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"DRAIN WATER FROM FUEL FILTER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly Level warning switch (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
"OIL MAINTENANCE REQUIRED SOON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"OIL MAINTENANCE REQUIRED" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
Oil maintenance required reset message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
Oil maintenance reset complete message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
Oil maintenance reset unfinished message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"CHECK HEADLIGHT SYSTEM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for LED Headlight) Lighting system (Click here)
Combination meter assembly (Click here)
"LOW WASHER FLUID" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Washer Fluid Level Warning System) Level warning switch assembly (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW FILL UP AdBlue IN **** km SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW FILL UP AdBlue IN **** MILES SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW FILL UP AdBlue IN **** km SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW FILL UP AdBlue IN **** MILES SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW NO START IN **** km! FILL UP AdBlue SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue LEVEL LOW NO START IN **** MILES! FILL UP AdBlue SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"AdBlue EMPTY UNABLE TO RESTART ENGINE FILL UP AdBlue SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"EMISSIONS TOO HIGH CHECK AdBlue VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"EMISSIONS TOO HIGH NO START IN **** km! CHECK AdBlue VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"EMISSIONS TOO HIGH NO START IN **** MILES! CHECK AdBlue VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"EMISSIONS TOO HIGH UNABLE TO RESTART ENGINE CHECK AdBlue VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"DPF FULL SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"DPF FULL VISIT YOUR DEALER" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"MANUAL REGENERATION IN PROCESS KEEP FLAMMABLES AWAY FROM VEHICLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"DPF REGENERATION IN PROCESS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"DPF MANUAL REGENERATION AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)
"DPF FULL MANUAL REGENERATION REQUIRED SEE OWNER'S MANUAL" message is displayed when it should not be, not displayed when it should be, or not displayed correctly ECD system (for 1GD-FTV, w/ Urea SCR System) (Click here)
Combination meter assembly (Click here)

Buzzer
Symptom Suspected Area See page
All buzzers do not operate normally Combination meter assembly (Click here)
Seat belt warning buzzer does not operate (Front seat belt warning light operates normally) Check customize setting (Click here)
Combination meter assembly (Click here)
Shift down reject buzzer does not operate*1 Automatic transmission system (for 1GR-FE) (Click here)
Automatic transmission system (for 2TR-FE) (Click here)
Automatic transmission system (for 1GD-FTV) (Click here)
Combination meter assembly (Click here)
Key reminder buzzer does not operate*2 Key reminder warning system (Click here)
Sliding roof open warning buzzer does not operate*3 Sliding roof control system (Click here)
Combination meter assembly (Click here)
Driving with parking brake unreleased warning buzzer does not operate (Speedometer and brake warning light are operate normally) Combination meter assembly (Click here)
Driving with any door opened warning buzzer does not operate (Speedometer and open door warning light operate normally) Combination meter assembly (Click here)
Multi-information display warning buzzer does not operate Combination meter assembly (Click here)
Entry and start system warning buzzer does not operate*4 Entry and start system (Click here)
Combination meter assembly (Click here)
Engine immobiliser certification buzzer does not operate Engine immobiliser system (w/ Entry and Start System) (Click here)
Engine immobiliser system (w/o Entry and Start System) (Click here)
Combination meter assembly (Click here)
Light reminder buzzer does not operate*5 Combination meter assembly (Click here)
Dynamic radar cruise control low speed cancel buzzer does not operate*6 Dynamic radar cruise control system (Click here)
Combination meter assembly (Click here)
Dynamic radar cruise control warning buzzer does not operate*6 Dynamic radar cruise control system (Click here)
Combination meter assembly (Click here)
4WD buzzer does not operate Transfer system -
Combination meter assembly (Click here)
Shift position R buzzer does not operate*7 Back-up light switch (Click here)
Combination meter assembly (Click here)
Speed limit exceeded buzzer does not operate*8 Speed signal circuit (Click here)
Combination meter assembly (Click here)
SEDIMENT buzzer does not operate (SEDIMENT warning light operate normally)*9 Combination meter assembly (Click here)
Master warning buzzer does not operate (Master warning light operate normally)*10 Combination meter assembly (Click here)
VSC buzzer does not operate*11 Vehicle stability control system (for Hydraulic Brake Booster) (Click here)
Vehicle stability control system (for Vacuum Brake Booster) (Click here)
Combination meter assembly (Click here)

*1: for Automatic Transmission (AC60F)

*2: w/o Entry and Start System

*3: w/ Sliding Roof System

*4: w/ Entry and Start System

*5: w/ Light Reminder System

*6: w/ Dynamic Radar Cruise Control System

*7: for Manual Transmission (RA61F)

*8: for Middle East

*9: w/ SEDIMENT Warning Light

*10: except Analog Meter, Segment Display Type

*11: w/ VSC


Others
Symptom Suspected Area See page
Other systems that use speed signal do not operate normally Speed signal circuit (Click here)
Customizable parameters cannot be changed (customizable parameters can be changed by using intelligent tester) Combination meter assembly (Click here)