The ECM constantly generates 5 V of power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated for several seconds when the engine switch is first turned to on (IG). The MIL goes off when the engine is started.
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and GTS on.
Check the communication between the GTS and ECM.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
B
A
Disconnect the throttle body with motor assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the throttle body with motor assembly connector.
Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).
B
A
Disconnect the accelerator pedal sensor assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the accelerator pedal sensor assembly connector.
B
A
Disconnect the VVT sensor (for Intake Side of Bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the VVT sensor (for Intake Side of Bank 1) connector.
B
A
Disconnect the VVT sensor (for Intake Side of Bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the VVT sensor (for Intake Side of Bank 2) connector.
B
A
Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
B
A
Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
B
A
Disconnect the power steering oil pressure switch connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate (for Automatic Transmission) | B |
| MIL does not illuminate (for Manual Transmission) | C |
Reconnect the power steering oil pressure switch connector.
B
A
C
Disconnect the emission control valve set connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the emission control valve set connector.
B
A
Disconnect the No. 2 emission control valve set connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the No. 2 emission control valve set connector.
B
A
Disconnect the throttle body with motor assembly connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the VVT sensor (for Intake Side of Bank 1) connector.
Disconnect the VVT sensor (for Intake Side of Bank 2) connector.
Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Disconnect the emission control valve set connector.
Disconnect the No. 2 emission control valve set connector.
Disconnect the power steering oil pressure switch connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-6 (VCPA) - Body ground | Always | 10 kΩ or higher |
| G56-3 (VCP2) - Body ground | Always | 10 kΩ or higher |
| C36-2 (VCTA) - Body ground | Always | 10 kΩ or higher |
| C35-13 (VCAP) - Body ground | Always | 10 kΩ or higher |
| C34-12 (VCV1) - Body ground | Always | 10 kΩ or higher |
| C34-6 (VCV2) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connectors.
Reconnect the throttle body with motor assembly connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the VVT sensor (for Intake Side of Bank 1) connector.
Reconnect the VVT sensor (for Intake Side of Bank 2) connector.
Reconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Reconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Reconnect the emission control valve set connector.
Reconnect the No. 2 emission control valve set connector.
Reconnect the power steering oil pressure switch connector.
OK
NG
Disconnect the throttle body with motor assembly connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the VVT sensor (for Intake Side of Bank 1) connector.
Disconnect the VVT sensor (for Intake Side of Bank 2) connector.
Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Disconnect the power steering oil pressure switch connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-4 (VCPA) - Body ground | Always | 10 kΩ or higher |
| G56-2 (VCP2) - Body ground | Always | 10 kΩ or higher |
| C36-13 (VCTA) - Body ground | Always | 10 kΩ or higher |
| C34-15 (VCV1) - Body ground | Always | 10 kΩ or higher |
| C34-16 (VCV2) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connectors.
Reconnect the throttle body with motor assembly connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the VVT sensor (for Intake Side of Bank 1) connector.
Reconnect the VVT sensor (for Intake Side of Bank 2) connector.
Reconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Reconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Reconnect the power steering oil pressure switch connector.
OK
NG