The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil.
The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0335 | Either condition is met:
·
No crankshaft position sensor signal is sent to the ECM while cranking (1 trip detection logic). ·
No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic). |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
Crankshaft (crank angle sensor plate) ·
ECM |
| P0339 | Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) The engine speed is 1000 rpm or more. (b) The starter signal is off. (c) 3 seconds or more have elapsed since the starter signal switched from on to off. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
Crankshaft (crank angle sensor plate) ·
ECM |
Reference: Inspection using an oscilloscope (VV1, VV2 and NE Signal Waveforms).
The correct waveforms are as shown.
VV1+ and VV2+ are the VVT sensor signals, and NE+ is the crankshaft position sensor signal.
Grounding failure of the shielded wire may cause noise in the waveforms.
| Item | Content |
|---|---|
| Terminal | VV1+ - VV1-
VV2+ - VV2- NE+ - NE- |
| Equipment Setting | 5 V/DIV.,
20 msec./DIV. |
| Condition | Cranking or idling |
If there is no signal from the crankshaft position sensor despite the engine running, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.
Check the engine speed. The engine speed can be checked by using the GTS. To check the engine speed, perform the procedures below:
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
Start the engine.
Read the values displayed on the GTS while the engine is running.
Correct values are displayed.
To check the engine speed change, display the graph on the GTS.
If the engine does not start, check the engine speed while cranking.
If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.
OK
NG
Inspect the crankshaft position sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSPECTION).
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-1 - C34-16 (NE+) | Always | Below 1 Ω |
| C14-2 - C34-17 (NE-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-1 - C34-6 (NE+) | Always | Below 1 Ω |
| C14-2 - C34-5 (NE-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-1 or C34-16 (NE+) - Body ground | Always | 10 kΩ or higher |
| C14-2 or C34-17 (NE-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-1 or C34-6 (NE+) - Body ground | Always | 10 kΩ or higher |
| C14-2 or C34-5 (NE-) - Body ground | Always | 10 kΩ or higher |
Reconnect the crankshaft position sensor connector.
Reconnect the ECM connector.
OK
NG
Check the crankshaft position sensor installation.
Sensor is installed correctly.
OK
NG
Check the teeth of the sensor plate.
Sensor plate does not have any cracks or deformation.
OK
NG
Replace the crankshaft position sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No output | A |
| P0335 or P0339 | B |
If the engine does not start, replace the ECM.
A
B