Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2431  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1  P2432  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1  P2433  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1  P2436  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Bank2  P2437  Open in Secondary Air Injection System Air Flow / Pressure Sensor Circuit Bank2  P2438  Short in Secondary Air Injection System Air Flow / Pressure Sensor Circuit Bank2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0412).

Refer to DTC P0416 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0416).

DTC No. DTC Detection Condition Trouble Area
P2431
P2436
Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) for 5 seconds or more (2 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


P2432
P2437
While the engine is running, voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


P2433
P2438
While the engine is running, voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic)
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM



MONITOR DESCRIPTION

A085160E40
0.073,2.771 1.125,2.948 1.052,0.177 10 false Pressure Sensor 2.594,2.927 2.917,3.104 0.323,0.177 10 false ECM 2.292,0.833 2.688,1.01 0.396,0.177 10 false VCAP 2.292,1.479 2.531,1.656 0.24,0.177 10 false AIP 0.833,1.615 1.073,1.792 0.24,0.177 10 false AIP 2.292,2.094 2.656,2.281 0.365,0.188 10 false EAIP 0.865,1.031 1.073,1.208 0.208,0.177 10 false VC 0.875,2.208 1.063,2.385 0.188,0.177 10 false E2 0.083,0.042 2.156,0.271 2.073,0.229 10 false Reference (for Bank 1):

The ECM monitors the pressure inside the air passage of the secondary air injection system using the pressure sensor of the air switching valve assembly. If the ECM detects a malfunction in the sensor or sensor circuit, it stores a DTC.

WIRING DIAGRAM

A162276E18
1.323,1.192 1.556,1.362 0.232,0.170 10 VC 1.665,1.368 1.815,1.518 0.149,0.149 10 2 1.281,1.76 1.555,1.930 0.274,0.170 10 AIP 5.655,1.175 6.063,1.344 0.408,0.170 10 VCAP 5.655,1.76 5.929,1.930 0.274,0.170 10 AIP 1.665,1.936 1.815,2.085 0.149,0.149 10 3 1.344,2.313 1.556,2.483 0.211,0.170 10 E2 1.665,2.489 1.815,2.638 0.149,0.149 10 4 0.32,2.825 0.596,2.993 0.276,0.168 10 C44 0.32,2.994 2.290,3.162 1.970,0.168 10 Emission Control Valve Set 1.246,3.714 1.647,3.884 0.401,0.170 10 VC2 1.665,3.89 1.815,4.039 0.149,0.149 10 2 1.223,4.282 1.555,4.451 0.332,0.170 10 AIP2 1.665,4.458 1.815,4.607 0.149,0.149 10 3 1.251,4.835 1.555,5.005 0.304,0.170 10 E22 1.665,5.011 1.815,5.160 0.149,0.149 10 4 0.32,5.346 0.596,5.514 0.276,0.168 10 C45 0.32,5.516 2.436,5.684 2.116,0.168 10 No. 2 Emission Control Valve Set 5.354,1.104 5.533,1.283 0.179,0.179 10 13 5.306,1.273 5.593,1.430 0.288,0.157 10 C35 5.354,1.678 5.574,1.857 0.220,0.179 10 15 5.306,1.843 5.593,1.999 0.288,0.157 10 C35 5.655,4.282 6.003,4.451 0.348,0.170 10 AIP2 5.354,4.2 5.603,4.378 0.249,0.179 10 16 5.306,4.365 5.593,4.521 0.288,0.157 10 C35 5.655,4.827 6.107,4.997 0.452,0.170 10 EAIP 6.053,5.804 6.428,5.973 0.376,0.170 10 ECM 5.354,4.745 5.626,4.924 0.272,0.179 10 14 5.306,4.91 5.593,5.067 0.288,0.157 10 C35

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)
a.

Disconnect the pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C44-3 (AIP) - C35-15 (AIP) Always Below 1 Ω
C44-2 (VC) - C35-13 (VCAP) Always Below 1 Ω
C44-4 (E2) - C35-14 (EAIP) Always Below 1 Ω
C45-3 (AIP2) - C35-16 (AIP2) Always Below 1 Ω
C45-2 (VC2) - C35-13 (VCAP) Always Below 1 Ω
C45-4 (E22) - C35-14 (EAIP) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C44-3 (AIP) or C35-15 (AIP) - Body ground Always 10 kΩ or higher
C44-2 (VC) or C35-13 (VCAP) - Body ground Always 10 kΩ or higher
C45-3 (AIP2) or C35-16 (AIP2) - Body ground Always 10 kΩ or higher
C45-2 (VC2) or C35-13 (VCAP) - Body ground Always 10 kΩ or higher



d.

Reconnect the pressure sensor connector.


e.

Reconnect the ECM connector.



OK

2.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) or Air Pump2 pressure (Absolute).


d.

Check the pressure displayed on the GTS.

Standard pressure:

45 to 135 kPa


HINT:

The GTS displays the air pump pressure as an absolute pressure.


Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C



A

B

C