Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0017  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)  P0019  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)  


DESCRIPTION

Refer to DTC P0013 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0013).

DTC No. DTC Detection Condition Trouble Area
P0017 Deviations in crankshaft and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side of bank 1, 2)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


P0019 Deviations in crankshaft and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0017 OR P0019)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0017 or P0019 is output A
DTC P0017 or P0019 and other DTCs are output B

HINT:

If any DTCs other than P0017 or P0019 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 1 OR BANK 2))

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 1 OR BANK 2))
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).


e.

Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

OK:
GTS Operation Engine Condition
0% (OFF) Normal engine idle speed
127% (ON) Engine idles roughly or stalls soon after camshaft timing oil control valve assembly switched from off to on




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH OR WHETHER TIMING CHAIN HAS JUMPED TOOTH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Drive the vehicle for more than 10 minutes.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0017 or P0019 is output B

HINT:

DTC P0017 or P0019 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.




A

B

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH OR WHETHER TIMING CHAIN HAS JUMPED TOOTH)
4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH OR WHETHER TIMING CHAIN HAS JUMPED TOOTH)

OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)
a.

Inspect the camshaft timing oil control valve assembly (for exhaust side of bank 1, 2) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

OK

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly (bank 1 or bank 2) (See page Engine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Drive the vehicle for more than 10 minutes.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read the pending DTCs.

Result
Result Proceed to
No DTC is output A
DTC P0017 or P0019 is output B



A

REPAIR COMPLETED

B