Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1520  Stop Light Switch Circuit Malfunction  


DESCRIPTION

In this system, the signal of the stop light switch is used to judge whether the stop light system is abnormal or not.

The stop light switch has a duplex system (signals STP and ST1-) to recognize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:

The normal condition is shown in the table below.

Signal Brake Pedal Released In Transition Brake Pedal Depressed
STP Off On On
ST1- On On Off

DTC No. DTC Detection Condition Trouble Area
P1520 Conditions (a), (b) and (c) continue for 0.5 seconds or more(1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is off when ST1- signal is off.
·

Open or short in stop light switch signal circuit

·

Stop light switch

·

ECM




WIRING DIAGRAM

A311394E03
0.784,0.874 1.851,1.081 1.067,0.206 10 from IG2 Relay 0.915,1.862 1.797,2.068 0.881,0.206 10 from Battery 2.452,1.042 2.760,1.198 0.309,0.156 10 IGN 4.553,1.796 4.686,1.949 0.132,0.153 10 2 5.896,3.099 6.279,3.252 0.383,0.153 10 ECM 3.405,1.796 3.537,1.949 0.132,0.153 10 1 3.405,0.787 3.537,0.940 0.132,0.153 10 5 5.303,0.801 5.498,0.954 0.194,0.153 10 10 5.399,1.788 5.533,1.941 0.134,0.153 10 9 5.604,0.801 5.952,0.954 0.348,0.153 10 ST1- 5.604,1.789 5.952,1.942 0.348,0.153 10 STP 4.553,0.797 4.686,0.950 0.132,0.153 10 4 2.387,2.033 2.798,2.189 0.411,0.156 10 STOP 3.468,2.868 4.607,3.055 1.139,0.187 10 Stop Light Switch 5.896,2.948 6.352,3.111 0.456,0.163 10 G182 3.465,2.687 3.920,2.850 0.455,0.163 10 A85 4.553,2.23 4.686,2.383 0.132,0.153 10 3 3.636,1.889 3.944,2.045 0.309,0.156 10 B 3.636,0.895 3.944,1.051 0.309,0.156 10 B 4.343,1.889 4.652,2.045 0.309,0.156 10 L 4.343,0.895 4.652,1.051 0.309,0.156 10 L 4.117,2.328 4.528,2.483 0.411,0.156 10 GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
U149408E01
0.587,1.151 0.863,1.306 0.276,0.156 10 A85 0.116,0.072 0.385,0.261 0.269,0.189 10 *a 2.224,1.866 2.387,2.029 0.163,0.163 10 B 2.051,1.402 2.263,1.866 false 1.141,1.866 1.304,2.029 0.163,0.163 10 B 1.398,1.402 1.215,1.866 false

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A85-1 (B) - Body ground Always 11 to 14 V
A85-5 (B) - Body ground Ignition switch ON 11 to 14 V


*a Front view of wire harness connector
(to Stop Light Switch Assembly)


c.

Reconnect the stop light switch assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODYGROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - INTEGRATION RELAY, BATTERY)

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODYGROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-3 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the stop light switch assembly connector.



OK

3.CHECK ECM (STP, ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (STP, ST1- VOLTAGE)
a.
A303106E01
1.938,2.427 2.354,2.688 0.417,0.26 0.552,2.438 0.969,2.698 0.417,0.26 1.813,3.938 2.188,3.177 true 2.615,3.906 2.26,3.177 true 1.063,3.896 0.667,3.083 true 1.99,2.479 2.365,2.677 0.375,0.198 10 false C182 2.375,3.948 2.979,4.198 0.604,0.25 10 false 9 (STP) 1.573,3.969 2.198,4.219 0.625,0.25 10 false 10 (ST1-) 0.604,2.49 0.979,2.688 0.375,0.198 10 false C161 0.917,3.927 1.521,4.177 0.604,0.25 10 false 5 (E1)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G182-9 (STP) - C161-5 (E1) Depressed 11 to 14 V
Released Below 1.5 V
G182-10 (ST1-) - C161-5 (E1) Depressed Below 1.5 V
Released 11 to 14 V


Text in Illustration
*a Brake pedal depressed
*b Brake pedal released
*c Component with harness connected
(ECM)



OK

NG

4.CHECK HARNESS AND CONNECTOR
4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-2 - G182-9 (STP) Always Below 1 Ω
A85-4 - G182-10 (ST1-) Always Below 1 Ω
A85-2 or G182-9 (STP) - Body ground Always 10 kΩ or higher
A85-4 or G182-10 (ST1-) - Body ground Always 10 kΩ or higher



d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the ECM connector.



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR