Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM J

5L-E ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The MIL is used to inform the user when the ECM has detected a vehicle malfunction.

By turning the ignition switch to ON, power is supplied to the MIL circuit and the ECM provides the circuit ground that illuminates the MIL.

Operation of the MIL should be checked visually: When the ignition switch is first turned to ON, the MIL should illuminate. When the engine is started, the MIL should turn off.

WIRING DIAGRAM

A227426E07
0.99,3.052 1.313,3.24 0.323,0.188 10 false ST 6.083,0.76 6.344,0.948 0.26,0.188 10 false W 1.969,2.896 2.438,3.094 0.469,0.198 10 false AM2 0.396,2.083 0.823,2.271 0.427,0.188 10 false P/I-B 6.344,4.146 6.76,4.375 0.417,0.229 10 false ECM 1.75,2.75 1.896,2.927 0.146,0.177 10 false 7 3.01,2.76 3.177,2.906 0.167,0.146 10 false 6 0.521,3.823 1.188,4 0.667,0.177 10 false Battery 0.635,0.667 0.813,0.813 0.177,0.146 10 false 1 1.042,0.979 1.365,1.167 0.323,0.188 10 false IG2 0.594,0.844 0.833,0.99 0.24,0.146 10 false 1C 1.438,1.885 2.948,2.115 1.51,0.229 10 false No. 1 Integration Relay 3.646,1.385 5.625,1.594 1.979,0.208 10 false Combination Meter Assembly 2.865,1 3.469,1.24 0.604,0.24 10 false GAUGE 2.635,2.896 2.969,3.083 0.333,0.188 10 false IG2 2.26,0.677 2.438,0.823 0.177,0.146 10 false 5 2.188,0.865 2.427,1.01 0.24,0.146 10 false 1A 2.25,1.115 2.427,1.26 0.177,0.146 10 false 1 2.188,1.292 2.427,1.438 0.24,0.146 10 false 1A 5.083,0.667 5.26,0.844 0.177,0.177 10 false 7 5.021,0.854 5.26,1 0.24,0.146 10 false G7 3.802,0.667 3.979,0.813 0.177,0.146 10 false 28 3.781,0.854 4.021,1 0.24,0.146 10 false G6 0.958,1.635 1.135,1.813 0.177,0.177 10 false 3 1.146,1.646 1.385,1.792 0.24,0.146 10 false 1A 5.813,0.75 6.104,0.938 0.292,0.188 10 false 13 6.344,3.979 6.802,4.125 0.458,0.146 10 false G182 1.656,1.521 1.979,1.698 0.323,0.177 10 false IG2 4.104,1.01 4.438,1.188 0.333,0.177 10 false IG+ 4.583,1.031 4.99,1.208 0.406,0.177 10 false CHK 1.677,3.479 3.396,3.719 1.719,0.24 10 false Ignition Switch Assembly 1.677,3.333 2.146,3.531 0.469,0.198 10 false G2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK MIL CONDITION
a.

Check the MIL condition.

Result:
Condition Proceed to
MIL remains on A
MIL does not illuminate B




A

2.CHECK IF MIL TURNS OFF

B

5.CHECK IF MIL ILLUMINATES
2.CHECK IF MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check if DTCs have been stored (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR). If DTCs are stored, write them down.



e.

Check that the MIL turns off.

OK:

The MIL turns off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (FOR SHORT)
3.CHECK HARNESS AND CONNECTOR (FOR SHORT)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

The MIL is not illuminated.



d.

Reconnect the ECM connector.



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G182-13 (W) - G7-7 (CHK) Always Below 1 Ω
G182-13 (W) or G7-7 (CHK) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter assembly connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK IF MIL ILLUMINATES
a.

Check that the MIL illuminates when turning the ignition switch to ON.

OK:

The MIL illuminates.




OK

NORMAL

NG

6.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
6.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

Refer to the combination meter assembly troubleshooting procedures (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY