Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM J

5L-E ENGINE CONTROL  ECD SYSTEM  Air Conditioning Cut Control Circuit  


DESCRIPTION

This circuit cuts air conditioning operation during vehicle acceleration in order to increase acceleration performance. During acceleration with the vehicle speed at 30 km/h (19 mph) or less and the accelerator pedal opening angle at 45° or more, the A/C magnetic switch is turned off for several seconds.

The air conditioning is also controlled using the engine coolant temperature output from the ECM to the A/C amplifier.

WIRING DIAGRAM

A227852E10
5.917,2.323 6.354,2.521 0.438,0.198 10 false ECM 0.448,2 1.365,2.208 0.917,0.208 10 false A/C ECU 0.448,1.833 0.875,2.063 0.427,0.229 10 false G25 5.906,2.156 6.375,2.354 0.469,0.198 10 false G183 5.563,0.865 6,1.063 0.438,0.198 10 false ACT 5.313,0.698 5.521,0.885 0.208,0.188 10 false 9 1.021,0.813 1.458,1.01 0.438,0.198 10 false ACT 1.448,0.688 1.781,0.875 0.333,0.188 10 false 27

PROCEDURE

1.READ VALUE USING GTS (CHECK OPERATION OF AIR CONDITIONING CUT CONTROL)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the air conditioning switch on.

HINT:

The A/C magnetic clutch is turned on.



c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / A/C Cut SIG.


d.

Check operation of the A/C magnetic clutch cut when air conditioning cut control is operated by the GTS.

OK:

A/C magnetic clutch is turned off.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ECM (ACT VOLTAGE)
2.INSPECT ECM (ACT VOLTAGE)
a.
U169097E02
2.323,1.625 2.938,0.875 false 2.563,0.344 3,0.51 0.438,0.167 10 false G183 0.135,0.052 0.365,0.219 0.229,0.167 10 false *a 1.979,1.635 2.583,1.823 0.604,0.188 10 false 9 (AC1)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G183-9 (ACT) - Body ground Engine idling 11 to 14 V
G183-9 (ACT) - Body ground Ignition switch ON, engine stopped 0 to 3 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER)
3.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the A/C amplifier connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G25-27 (ACT) - G183-9 (ACT) Always Below 1 Ω
G25-27 (ACT) or G183-9 (ACT) - Body ground Always 10 kΩ or higher



d.

Reconnect the A/C amplifier connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR