Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor  


DESCRIPTION

The vehicle speed sensor outputs a 4 pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter assembly, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A260993E02
1.063,1.229 1.531,1.667 0.469,0.438 10 false Speed Sensor 2.01,0.552 3.125,0.854 1.115,0.302 10 false 4-Pulse Signal 3,2.01 4.365,2.385 1.365,0.375 10 false Combination Meter 4.271,0.552 5.385,0.844 1.115,0.292 10 false 4-Pulse Signal 5.688,1.25 6.073,1.677 0.385,0.427 10 false ECM

DTC No. DTC Detection Condition Trouble Area
P0500 All conditions below are detected continuously for 8 second or more:
1.

No speed signal is input to the ECM.

2.

Engine speed is 2000 to 3300 rpm.

3.

Engine coolant temperature is 70°C (158°F) or more.

4.

Accelerator pedal opening angle is 60% or more.


·

Open or short in speed sensor circuit

·

Speed sensor

·

Combination meter assembly

·

Skid Control ECU

·

ECM



MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated engine speed is 2000 to 3300 rpm and the engine load calculated by the ECM is more than a certain level. If there is no signal from the speed sensor, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM

A340550E09
6.177,0.792 6.427,0.948 0.25,0.156 10 false 5 V 5.406,1.042 5.729,1.198 0.323,0.156 10 false SP1 5.167,1.094 5.375,1.25 0.208,0.156 10 false 25 5.938,2 6.406,2.146 0.469,0.146 10 false G182 5.938,2.146 6.292,2.313 0.354,0.167 10 false ECM 4.469,1.083 4.719,1.24 0.25,0.156 10 false 32 2.688,1.094 2.906,1.25 0.219,0.156 10 false 33 3.115,2 3.417,2.167 0.302,0.167 10 false G6 0.115,2 0.417,2.167 0.302,0.167 10 false A7 4.198,1.094 4.417,1.26 0.219,0.167 10 false +S 1.948,1.094 2.177,1.25 0.229,0.156 10 false 12 1.563,1.104 1.885,1.271 0.323,0.167 10 false SP1 2.969,1.094 3.135,1.26 0.167,0.167 10 false SI 3.115,2.135 4.323,2.302 1.208,0.167 10 false Combination Meter 0.115,2.167 2.323,2.406 2.208,0.24 10 false Skid Control ECU (Brake Actuator)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speed displayed on GTS and speedometer display are equal.




OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the combination meter system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


b.

During inspection for the combination meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.



NEXT

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-32 (+S) - G182-25 (SP1) Always Below 1 Ω
G6-32 (+S) or G182-25 (SP1) - Body ground Always 10 kΩ or higher


HINT:

If the wire has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. tire pressure warning system, audio system, etc.).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)