Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A227732E02
6.188,2.563 6.552,2.74 0.365,0.177 10 false ECM 6.188,2.406 6.479,2.573 0.292,0.167 10 false G57 6,1.01 6.229,1.188 0.229,0.177 10 false W 4.917,1.104 5.146,1.281 0.229,0.177 10 false G7 2.74,1.115 2.969,1.292 0.229,0.177 10 false G6 3.99,1.292 4.26,1.458 0.271,0.167 10 false MIL 3.042,1.219 3.302,1.385 0.26,0.167 10 false IG+ 4.5,1.219 4.865,1.396 0.365,0.177 10 false CHK 2.75,0.938 2.938,1.115 0.188,0.177 10 false 28 4.969,0.917 5.083,1.073 0.115,0.156 10 false 7 3.313,2.042 4.542,2.25 1.229,0.208 10 false Combination Meter 0.469,1.094 1.583,1.354 1.115,0.26 10 false from IG2 Relay 1.906,1.271 2.438,1.417 0.531,0.146 10 false GAUGE 5.74,1 5.979,1.188 0.24,0.188 10 false 19

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Check the MIL illumination condition.

Result
Condition Proceed to
MIL remains on A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check if DTCs have been stored (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR). If DTCs are output, write them down.



e.

Check that the MIL turns off.

OK:

MIL turns off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



d.

Reconnect the ECM connector.



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G7-7 (CHK) - G57-19 (W) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G7-7 (CHK) or G57-19 (W) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination assembly meter connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL is illuminated.




OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

Refer to the combination meter troubleshooting procedure (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

REPLACE COMBINATION METER ASSEMBLY