Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The intake mass air flow meter assembly consists of a platinum hot wire, temperature sensor and control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.

There is little variation in the output from the intake mass air flow meter assembly, as it is hardly affected by the resistance of the wire harness.

The internal circuit of the intake mass air flow meter assembly contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illustration) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 1945 and 8500 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.

A221589E08
2.042,1.25 1.865,1.25 1.865,1.25 1.677,1.719 false 0.521,2.708 0.521,2.094 0.521,2.094 1.302,1.802 false 2.719,1.635 2.604,1.635 2.604,1.635 2.417,1.948 false 4.083,2.896 4.083,2.479 4.083,2.479 4.542,1.885 false 6.031,3.25 6.031,2.917 6.031,2.917 4.813,2.115 false 1.667,0.51 1.896,0.708 0.229,0.198 10 false +B 1.635,0.833 2.76,1.021 1.125,0.188 10 false Power Transistor 2.771,1.531 3.75,1.708 0.979,0.177 10 false Output Voltage 2.115,2.302 3.406,2.646 1.292,0.344 10 false Periodic Signal Conversion Circuit 2.198,3.323 3.417,3.5 1.219,0.177 10 false Output Frequency 0.052,2.719 1.333,3.063 1.281,0.344 10 false Temperature Sensor (Thermistor) 2.115,1.156 3.823,1.365 1.708,0.208 10 false Platinum Hot Wire (Heater) 3.563,2.927 5.281,3.125 1.719,0.198 10 false Platinum Hot Wire (Heater) 4.979,3.271 7.115,3.458 2.135,0.188 10 false Temperature Sensor (Thermistor)

P0102
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
3 seconds after engine is started Mass air flow meter signal frequency is less than 85 Hz with the engine speed at 5000 rpm or less for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM



P0103
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
3 seconds after engine is started Mass air flow meter signal frequency is more than 9800 Hz with the engine speed at 5000 rpm or less for 3 seconds (1 trip detection logic).
·

Open or short in Mass air flow meter circuit

·

Mass air flow meter

·

ECM



Related Data List
DTC No. Data List
P0102 MAF
P0103

HINT:
·

If DTC P0102 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):

-

Combustion noise worsens


·

If DTC P0103 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is more air than the actual intake air amount, EGR is increased according to the target EGR):

-

Misfire

-

White smoke

-

Black smoke




WIRING DIAGRAM

A221588E03
0.62,3.087 1.164,3.276 0.543,0.189 10 Battery 0.465,2.322 0.829,2.505 0.364,0.184 10 P/I-B 1.187,0.851 1.454,1.020 0.267,0.170 10 EFI 1.852,1.397 2.133,1.553 0.281,0.156 10 EFI 1.572,1.719 3.325,2.097 1.753,0.378 10 No. 1 Integration Relay (Engine Room Relay Block) 3.827,2.088 5.136,2.244 1.309,0.156 10 Mass Air Flow Meter 2.959,0.851 3.668,1.006 0.709,0.156 10 EFI NO. 2 6.2,3.316 6.546,3.472 0.346,0.156 10 ECM 5.415,1.028 5.715,1.207 0.299,0.179 10 C90 5.415,1.539 5.715,1.718 0.299,0.179 10 C90 5.406,2.807 5.705,2.986 0.299,0.179 10 G58 3.827,1.925 4.127,2.104 0.299,0.179 10 C33 5.471,0.841 5.660,1.020 0.188,0.179 10 17 5.467,1.355 5.655,1.534 0.188,0.179 10 18 5.471,2.635 5.660,2.814 0.188,0.179 10 11 5.084,1.117 5.209,1.296 0.126,0.179 10 5 5.084,1.63 5.207,1.809 0.123,0.179 10 4 3.699,0.811 3.804,0.990 0.105,0.179 10 3 2.501,0.713 2.743,0.892 0.242,0.179 10 1B 2.501,1.057 2.710,1.236 0.209,0.179 10 1B 1.352,1.49 1.572,1.669 0.220,0.179 10 1B 0.756,0.707 0.958,0.886 0.202,0.179 10 1C 0.806,0.545 0.925,0.696 0.119,0.151 10 1 2.555,0.552 2.674,0.703 0.119,0.151 10 4 2.564,1.224 2.683,1.375 0.119,0.151 10 2 1.163,1.49 1.282,1.642 0.119,0.151 10 3 5.754,0.938 5.993,1.101 0.239,0.163 10 VG 5.754,1.449 6.083,1.612 0.330,0.163 10 EVG 5.754,2.736 6.176,2.899 0.422,0.163 10 MREL 3.89,0.621 4.130,0.783 0.239,0.163 10 +B 4.801,0.938 5.040,1.101 0.239,0.163 10 VG 4.717,1.438 5.030,1.601 0.313,0.163 10 E2G

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT)
U169083E02
1.719,1.125 1.438,1.688 true 1.302,1.708 1.531,1.896 0.229,0.188 10 false +B 0.188,0.188 0.385,0.385 0.198,0.198 10 false *a 0.354,1.01 0.677,1.219 0.323,0.208 10 false C33

a.

Disconnect the mass air flow meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C33-3 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to mass air flow meter)


c.

Reconnect the mass air flow meter connector.



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C33-5 (VG) - C90-17 (VG) Always Below 1 Ω
C33-4 (E2G) - C90-18 (EVG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C33-5 (VG) or C90-17 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

6.REPLACE MASS AIR FLOW METER

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK)
a.

Disconnect the mass air flow meter connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C33-3 (+B) - 1B-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C33-3 (+B) or 1B-4 - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reinstall the No. 1 integration relay.



OK

5.CHECK ECM POWER SOURCE CIRCUIT

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK ECM POWER SOURCE CIRCUIT

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE MASS AIR FLOW METER

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.



c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
P0102 or P0103 A
No output B



A

8.REPLACE ECM

B

END

8.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Confirm that the DTC is not output again.



NEXT

END