Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A264726E01
0.655,1.251 0.978,1.416 0.323,0.165 10 ST 2.172,1.012 3.990,1.173 1.818,0.161 10 Ignition Switch Assembly*2 5.659,0.431 6.014,0.587 0.355,0.156 10 IG2D 5.039,0.678 5.395,0.839 0.356,0.161 10 G50 5.417,0.319 5.522,0.475 0.105,0.156 10 8 4.92,0.814 7.131,0.970 2.211,0.156 10 Power Management Control ECU*1 0.82,4.83 1.290,5.009 0.471,0.179 10 Battery 1.296,3.261 1.632,3.417 0.336,0.156 10 P/I-B 2.221,3.831 2.432,3.987 0.211,0.156 10 1C 2.235,4.092 2.446,4.248 0.211,0.156 10 1B 2.272,3.672 2.382,3.823 0.110,0.151 10 1 2.221,2.202 2.432,2.358 0.211,0.156 10 1A 2.272,2.043 2.382,2.195 0.110,0.151 10 3 2.272,4.256 2.382,4.407 0.110,0.151 10 3 4.266,3.831 4.478,3.987 0.211,0.156 10 1B 4.266,4.092 4.478,4.248 0.211,0.156 10 1B 4.318,3.672 4.427,3.823 0.110,0.151 10 4 4.318,4.256 4.427,4.407 0.110,0.151 10 2 4.266,1.946 4.478,2.102 0.211,0.156 10 1A 4.266,2.207 4.478,2.363 0.211,0.156 10 1A 4.318,1.787 4.427,1.938 0.110,0.151 10 5 4.318,2.371 4.427,2.522 0.110,0.151 10 1 3.612,3.532 3.923,3.688 0.311,0.156 10 EFI 2.795,3.709 3.039,3.865 0.244,0.156 10 EFI 3.617,2.504 3.879,2.660 0.262,0.156 10 IG2 2.786,1.833 3.048,1.989 0.262,0.156 10 IG2 5.032,1.813 5.313,1.974 0.281,0.161 10 IGN 5.504,1.944 5.873,2.104 0.369,0.161 10 G58 5.516,3.487 5.830,3.648 0.314,0.161 10 G57 5.513,4.09 5.844,4.250 0.331,0.161 10 G58 5.509,4.587 5.832,4.747 0.323,0.161 10 C93 5.519,3.824 5.844,3.984 0.325,0.161 10 G57 5.555,1.766 5.730,1.927 0.174,0.161 10 24 5.574,3.322 5.748,3.482 0.174,0.161 10 17 5.574,3.667 5.748,3.828 0.174,0.161 10 24 5.582,4.27 5.762,4.430 0.180,0.161 10 11 5.616,4.75 5.790,4.910 0.174,0.161 10 1 6.204,5.073 6.550,5.238 0.346,0.165 10 ECM 5.854,1.85 6.255,2.011 0.401,0.161 10 IGSW 5.854,3.48 6.144,3.641 0.290,0.161 10 +B2 5.854,3.835 6.063,3.996 0.209,0.161 10 +B 5.854,4.097 6.278,4.257 0.424,0.161 10 MREL 5.854,4.586 6.052,4.747 0.198,0.161 10 E1 2.5,4.58 4.342,4.919 1.842,0.339 10 No. 1 Integration Relay (Engine Room Relay Block) 1.499,5.122 3.419,5.285 1.920,0.163 10 *1: w/ Entry and Start System 1.499,5.416 3.440,5.572 1.941,0.156 10 *2: w/o Entry and Start System 2.183,0.845 2.505,1.010 0.323,0.165 10 G2 2.312,0.555 2.634,0.724 0.323,0.170 10 AM2 2.907,0.555 3.174,0.724 0.267,0.170 10 IG2 2.165,0.309 2.300,0.479 0.135,0.170 10 7 3.215,0.309 3.350,0.479 0.135,0.170 10 6

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.INSPECT NO. 1 INTEGRATION RELAY (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.
U147598E02
0.594,1.573 0.917,1.948 true 0.49,1.042 0.688,1.208 0.198,0.167 10 false 1C 0.083,0.083 0.365,0.313 0.281,0.229 10 false *a 0.094,3.917 0.396,4.135 0.302,0.219 10 false *1 0.958,1.896 1.156,2.104 0.198,0.208 10 false 1

Remove the No. 1 integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V


*1 Engine Room Relay Block
*a Front view of wire harness connector
(to No. 1 integration Relay)


c.

Reinstall the integration relay.



OK

2.INSPECT NO. 1 INTEGRATION RELAY (EFI , IG2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 1 INTEGRATION RELAY (EFI , IG2)
a.

Inspect the No. 1 integration relay (EFI) (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).


b.

Inspect the No. 1 integration relay (IG2) (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

3.INSPECT ECM (IGSW VOLTAGE)

NG

REPLACE NO. 1 INTEGRATION RELAY

3.INSPECT ECM (IGSW VOLTAGE)
a.
U169107E02
0.677,0.938 0.469,1.563 true 3.229,0.74 2.927,1.594 true 0.75,0.333 1.042,0.5 0.292,0.167 10 false G58 2.958,0.333 3.25,0.5 0.292,0.167 10 false C93 2.708,1.625 3.167,1.865 0.458,0.24 10 false 1 (E1) 0.083,1.594 0.896,1.823 0.813,0.229 10 false 24 (IGSW) 0.125,0.021 0.313,0.188 0.188,0.167 10 false *a

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G58-24 (IGSW) - C93-1 (E1) Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(to ECM)


Result
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C


A

4.CHECK WIRE HARNESS (NO. 1 INTEGRATION RELAY - ECM)

B

5.CHECK WIRE HARNESS (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

C

6.CHECK WIRE HARNESS (IGNITION SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
4.CHECK WIRE HARNESS (NO. 1 INTEGRATION RELAY - ECM)
a.

Check the wire harness between the ECM and No. 1 integration relay.


b.

Disconnect the ECM connector.


c.

Remove the No. 1 integration relay from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G58-11 (MREL) - 1B-2 Always Below 1 Ω
G57-24 (+B) - 1B-4 Always Below 1 Ω
G57-17 (+B2) - 1B-4 Always Below 1 Ω
G58-24 (IGSW) - 1A-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G58-11 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
G57-24 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
G57-17 (+B2) or 1B-4 - Body ground Always 10 kΩ or higher
G58-24 (IGSW) or 1A-5 - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Remove the power management control ECU.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G50-8 (IG2D) - 1A-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G50-8 (IG2D) or 1A-1 - Body ground Always 10 kΩ or higher



d.

Reinstall the power management control ECU.


e.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (IGNITION SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the ignition switch assembly connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G2-6 (IG2) - 1A-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G2-6 (IG2) or 1A-1 - Body ground Always 10 kΩ or higher



d.

Reconnect the ignition switch assembly connector.


e.

Reinstall the No. 1 integration relay.



OK

7.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1KD-FTV (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE IGNITION OR STARTER SWITCH ASSEMBLY