The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.
When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.
The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 3 seconds | Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic). | ·
Throttle position sensor ·
Open or short in VLU circuit ·
Open in VC circuit ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 3 seconds | Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic). | ·
Throttle position sensor ·
Open in E2 circuit ·
VC and VLU circuits are short-circuited ·
ECM |
If DTC P0122 and/or P0123 is stored, the following symptoms may appear:
- Intake booming noise
- Black smoke
- Lack of power
- Vibration at engine stop
- Turbo overspeed, turbo damage
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the throttle position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C73-1 (VC) - C91-8 (VCVL) | Always | Below 1 Ω |
| C73-3 (VTA) - C91-3 (VLU) | Always | Below 1 Ω |
| C73-2 (E2) - C91-9 (EVLU) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C73-1 (VC) or C91-8 (VCVL) - Body ground | Always | 10 kΩ or higher |
| C73-3 (VTA) or C91-3 (VLU) - Body ground | Always | 10 kΩ or higher |
| C73-2 (E2) or C91-9 (EVLU) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle position sensor connector.
Reconnect the ECM connector.
OK
NG
Disconnect the throttle position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C73-1 (VC) - C73-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector
(to throttle position sensor) |
Reconnect the throttle position sensor connector.
OK
NG
Replace the diesel throttle body assembly (for Bank 1 or Bank 2) (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Enter the following menus: Powertrain / Engine / Data List / Actual Throttle position or Actual Throttle position #2.
Check the movement of the throttle valve when idling the engine after starting it from ignition switch ON.
| Condition | Tester Display |
|---|---|
| Ignition switch ON | -5 to 5% |
| Idling | 0 to 90% |
OK
NG
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON for 3 seconds.
Enter the following menus: Powertrain / Engine / DTC.
Confirm that the DTC is not output again.
NEXT