Vehicles which are equipped with a manual transaxle detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Drive the vehicle at 10 km/h (6.3 mph) or more | Conditions (a), (b) and (c) are met for 8 seconds or more (2 trip detection logic):
(a) Engine coolant temperature is higher than 70°C (158°F). (b) Injection volume is 19 mm3/st or more. (c) No speed signal is input to the ECM. |
·
Open or short in speedometer circuit ·
Speedometer assembly ·
ECM |
| Drive the vehicle at 10 km/h (6.3 mph) or more | Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) The fuel-cut operation is being performed. (b) No speed signal is input to the ECM. |
| DTC No. | Data List |
|---|---|
| P0500 | Vehicle Speed |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.
The vehicle speed sensor is operating normally if the speedometer reading is normal.
The vehicle speed sensor is operating normally.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
Vehicle speed displayed on tester and speedometer display are equal.
OK
NG
Disconnect the combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-32 (+S) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector
(to combination meter assembly) |
Reconnect the combination meter assembly connector.
OK
NG
Move the shift lever to neutral.
Jack up the vehicle.
Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-32 (+S) - Body ground | Ignition switch ON | Voltage generated intermittently |
| *a | Component with harness connected
(combination meter assembly) |
The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-32 (+S) - G58-30 (SPD) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-32 (+S) or G58-30 (SPD) - Body ground | Always | 10 kΩ or higher |
Reconnect the combination meter assembly connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Check the speedometer circuit (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).
Inspect the brake actuator assembly and speed sensor.
NEXT
Replace the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at 10 km/h (6.3 mph) or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the pending DTC is not output again.
NEXT