The meter CPU receives vehicle speed signals from the skid control ECU via the CAN communication system. The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).
Before starting the following inspection, check tire size and tire air pressure.
Check if a CAN communication DTC is output.
for LHD with Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
for LHD without Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)>DIAGNOSIS SYSTEM).
for RHD with Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)>DIAGNOSIS SYSTEM).
for RHD without Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| CAN communication DTC is not output. | A |
| CAN communication DTC is output. (for LHD with entry and start system) | B |
| CAN communication DTC is output. (for LHD without entry and start system) | C |
| CAN communication DTC is output. (for RHD with entry and start system) | D |
| CAN communication DTC is output. (for RHD without entry and start system) | E |
A
B
C
D
E
Using the GTS, perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Speed Meter Operation | Speedometer | ·
OFF, 0, 40, 80, 120, 160 or 200 (km/h) (for km/h) ·
OFF, 0, 40, 80 or , 120 (mph) (for mph) |
There is a deviation in the values displayed on the speedometer display (Control range → Speedometer)
for km/h (except Australia):
·
40 → 41.7 to 46.2 ·
80 → 83.4 to 88.4 ·
120 → 125.1 to 130.6 ·
160 → 166.2 to 173.2 for km/h (for Australia):
·
40 → 40.8 to 45.3 ·
80 → 81.6 to 86.6 ·
120 → 122.4 to 127.4 ·
160 → 163.2 to 168.2 for mph:
·
40 → 42 to 44.5 ·
80 → 83.1 to 87.1 |
Speedometer indication is normal.
OK
NG
Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
OK
NG
Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Wheel Speed | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Almost same as actual vehicle speed | - |
| FL Wheel Speed | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Almost same as actual vehicle speed | - |
| RR Wheel Speed | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Almost same as actual vehicle speed | - |
| RL Wheel Speed | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Almost same as actual vehicle speed | - |
Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Hydraulic Brake Booster) | B |
| NG (for 2TR-FE, Vacuum Brake Booster) | C |
| NG (for 5L-E, Vacuum Brake Booster) | D |
A
B
C
D
Replace the skid control ECU with a new or normally functioning one.
for LHD Hydraulic Brake Booster (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>DISASSEMBLY).
for RHD Hydraulic Brake Booster (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for RHD)>DISASSEMBLY).
for 2TR-FE, 5L-E (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL).
Check that the operation of the speedometer returns to normal.
The operation of the speedometer returns to normal.
OK
NG