Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal switch conditions are as shown in the table below.

Signals Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


P0504
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Depress and release brake pedal with ignition switch ON Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM



Related Data List
DTC No. Data List
P0504 Stop Light Switch

WIRING DIAGRAM

A311394E01
0.784,0.874 1.851,1.081 1.067,0.206 10 from IG2 Relay 0.915,1.862 1.797,2.068 0.881,0.206 10 from Battery 2.424,0.705 2.732,0.861 0.309,0.156 10 IGN 4.553,1.796 4.686,1.949 0.132,0.153 10 2 5.896,3.099 6.279,3.252 0.383,0.153 10 ECM 3.426,1.796 3.558,1.949 0.132,0.153 10 1 3.405,0.787 3.537,0.940 0.132,0.153 10 5 5.394,0.801 5.506,0.954 0.112,0.153 10 9 5.394,1.788 5.496,1.941 0.102,0.153 10 8 5.604,0.801 5.952,0.954 0.348,0.153 10 ST1- 5.604,1.789 5.952,1.942 0.348,0.153 10 STP 4.559,0.797 4.691,0.950 0.132,0.153 10 4 2.373,1.697 2.784,1.853 0.411,0.156 10 STOP 3.468,2.938 4.607,3.125 1.139,0.187 10 Stop Light Switch 5.896,2.948 6.200,3.111 0.303,0.163 10 G57 3.465,2.757 3.920,2.920 0.455,0.163 10 A85 4.574,2.23 4.707,2.383 0.132,0.153 10 3 3.626,0.906 3.821,1.100 0.194,0.194 10 B 3.626,1.873 3.821,2.067 0.194,0.194 10 B 4.121,2.328 4.502,2.522 0.381,0.194 10 GND 4.327,0.885 4.521,1.079 0.194,0.194 10 L 4.327,1.864 4.521,2.058 0.194,0.194 10 L 2.87,2.092 3.281,2.248 0.411,0.156 10 Diode

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the intelligent tester.

(a)

Connect the intelligent tester to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the tester on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

(e)

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK ECM (STP AND ST1- VOLTAGE)
U169158E02
0.667,3.198 1.156,3.865 true 0.615,3.198 0.375,3.865 true 0.094,0.458 0.354,0.635 0.26,0.177 10 false *a 1.604,0.458 1.844,0.698 0.24,0.24 10 false *b 0.063,2.063 0.24,2.25 0.177,0.188 10 false *c 0.365,2.667 0.677,2.875 0.313,0.208 10 false G57 0.938,3.896 1.458,4.073 0.521,0.177 10 false 8 (STP) 0.083,3.896 0.677,4.073 0.594,0.177 10 false 9 (ST1-)

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G57-9 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
G57-8 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V


Text in Illustration
*a Brake pedal depressed
*b Brake pedal released
*c Component with harness connected
(ECM)


d.

Reconnect the ECM connector.



OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
U170665E01
0.587,1.151 0.863,1.306 0.276,0.156 10 A85 0.116,0.072 0.385,0.261 0.269,0.189 10 *a 2.224,1.866 2.387,2.029 0.163,0.163 10 B 2.051,1.402 2.263,1.866 false 1.141,1.866 1.304,2.029 0.163,0.163 10 B 1.398,1.402 1.215,1.866 false 1.519,1.866 1.897,2.029 0.378,0.163 10 GND 1.731,1.436 1.732,1.84 false

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-1 (B) - Body ground Always 11 to 14 V
A85-5 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch)


d.

Reconnect the stop light switch assembly connector.



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A85-2 (L) - G57-8 (STP) Always Below 1 Ω
A85-4 (L) - G57-9 (ST1-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A85-2 (L) or G57-8 (STP) - Body ground Always 10 kΩ or higher
A85-4 (L) or G57-9 (ST1-) - Body ground Always 10 kΩ or higher



d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Confirm that the DTC is not output again.

OK:

DTC is not output again.




OK

END

NG

7.REPLACE ECM
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Confirm that the DTC is not output again.



NEXT

END