Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.

A208460E66
2.771,0.5 2.938,0.25 2.938,0.25 2.99,0.25 false 3.135,2.177 3.24,2.125 3.24,2.125 3.281,2.125 false 1.948,1.656 2.177,1.656 false 2.229,1.115 2.5,1.115 false 1.406,0.521 0.938,0.635 false 0.063,0.031 1.854,0.25 1.792,0.219 10 false Property of Output Voltage: 1.052,0.385 1.365,0.542 0.313,0.156 10 false 5.00 0.625,0.552 0.938,0.708 0.313,0.156 10 false 4.90 2.229,1.583 3.01,1.823 0.781,0.24 10 false RR2 (Sub) 1.573,1.021 2.323,1.219 0.75,0.198 10 false RR (Main) 1.052,0.604 1.365,0.76 0.313,0.156 10 false 4.44 1.052,0.813 1.365,0.969 0.313,0.156 10 false 3.89 1.052,1.688 1.365,1.844 0.313,0.156 10 false 1.40 1.052,1.885 1.365,2.042 0.313,0.156 10 false 0.85 1.052,2.063 1.365,2.219 0.313,0.156 10 false 0.55 1.24,2.198 1.365,2.354 0.125,0.156 10 false 0 2.938,2.313 3.438,2.469 0.5,0.156 10 false 190000 1.333,2.417 2.646,2.594 1.313,0.177 10 false Fuel Pressure (kPa) 3.292,2.052 4.188,2.219 0.896,0.167 10 false Stores P0192 3.031,0.167 4.042,0.417 1.01,0.25 10 false Stores P0193 0.063,1.115 1.323,1.26 1.26,0.146 10 false Output Voltage (V) 5.198,1.156 5.552,1.323 0.354,0.167 10 false Main 5.26,1.906 5.552,2.073 0.292,0.167 10 false Sub 6.76,1.188 7.073,1.375 0.313,0.188 10 false PR 6.76,1.385 7.073,1.573 0.313,0.188 10 false E2 6.76,1.729 7.073,1.917 0.313,0.188 10 false VCS 6.76,1.938 7.073,2.125 0.313,0.188 10 false PR2 5.906,0.635 6.146,0.823 0.24,0.188 10 false VC 6.365,2.448 6.677,2.635 0.313,0.188 10 false E2S 4.219,0 6.771,0.417 2.552,0.417 10 false Internal Structure of the Pressure Sensor (Duplicate Systems):

P0087
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds Fuel pressure sensor output voltage stays at fixed value for 90 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail)

·

Ran out of fuel

·

Fuel frozen

·

ECM



P0190
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



P0192
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



P0193
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



Related Data List
DTC No. Data List
P0087
·

Fuel Press

·

Target Common Rail Pressure


P0190
P0192
P0193

HINT:
·

Check Fuel Press and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure. Under stable conditions, the difference between Fuel Press and Target Common Rail Pressure is 5000 kPa or less.

·

For more information on the fuel pressure sensor and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If DTC P0087 is stored, the following symptoms may appear:

-

Black smoke

-

Poor drivability

-

Lack of power

-

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, the following symptom may appear:

-

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, "Fuel Press" always displays 0 kPa or 200000 kPa.



MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):
·

Under normal conditions, the internal fuel pressure of the common rail usually fluctuates by 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 30000 to 40000 kPa (306 to 408 kgf/cm2, 4350 to 5800 psi) when idling, and it increases to approximately 45000 to 75000 kPa (459 to 765 kgf/cm2, 6527 to 10878 psi) when running the engine at 3000 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

·

The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.

U121330E02
4.698,1.802 4.188,1.438 false 4.698,1.802 4.833,1.802 false 5.417,0.573 5.615,0.573 false 0.063,0.052 1.906,0.26 1.844,0.208 10 false P0087 Malfunction Detection 2.271,0.552 3.229,0.771 0.958,0.219 10 false Fuel Pressure 4.885,1.719 5.552,1.917 0.667,0.198 10 false Abnormal 5.677,0.49 6.26,0.688 0.583,0.198 10 false Normal 2.292,2.167 3.24,2.375 0.948,0.208 10 false Engine Speed 5.229,3.375 5.615,3.542 0.385,0.167 10 false Time



P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A149601E50
0.281,3.198 1.719,3.406 1.438,0.208 10 false Fuel Pressure Sensor 5.604,1.271 6.063,1.479 0.458,0.208 10 false VCM 5.323,2.729 5.5,2.938 0.177,0.208 10 false 13 5.323,0.635 5.5,0.844 0.177,0.208 10 false 16 5.396,1.885 5.5,2.094 0.104,0.208 10 false 2 5.396,2.302 5.5,2.51 0.104,0.208 10 false 8 5.323,1.479 5.5,1.688 0.177,0.208 10 false 14 5.323,1.052 5.5,1.26 0.177,0.208 10 false 15 5.604,0.427 6,0.635 0.396,0.208 10 false PCR1 5.594,0.854 6.042,1.063 0.448,0.208 10 false E2M 5.604,2.521 6.052,2.729 0.448,0.208 10 false VCS 5.594,1.688 6.031,1.896 0.438,0.208 10 false PCR2 5.604,2.104 6.188,2.313 0.583,0.208 10 false E2S 1.646,1.375 2.104,1.583 0.458,0.208 10 false VC 1.646,0.542 1.958,0.75 0.313,0.208 10 false PR 1.667,0.948 2.01,1.156 0.344,0.208 10 false E2 1.563,2.625 2.01,2.833 0.448,0.208 10 false VCS 1.583,1.781 2.021,1.99 0.438,0.208 10 false PR2 1.583,2.198 2.01,2.406 0.427,0.208 10 false E2S 2,1.042 2.208,1.25 0.208,0.208 10 false 4 1.99,1.479 2.198,1.688 0.208,0.208 10 false 6 1.99,0.646 2.198,0.854 0.208,0.208 10 false 5 1.99,2.719 2.198,2.927 0.208,0.208 10 false 1 1.99,2.323 2.198,2.531 0.208,0.208 10 false 3 2,1.885 2.104,2.094 0.104,0.208 10 false 2 5.99,3.208 6.385,3.406 0.396,0.198 10 false ECM 5.99,3.052 6.292,3.26 0.302,0.208 10 false C90 0.281,3.042 0.563,3.229 0.281,0.188 10 false C82

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs relating to different systems which share terminal E2 as their ground are stored, check this ground circuit first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
P0190, P0192, P0193 A
P0087 B



A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C82-5 (PR) - C90-16 (PCR1) Always Below 1 Ω
C82-2 (PR2) - C90-2 (PCR2) Always Below 1 Ω
C82-1 (VCS) - C90-13 (VCS) Always Below 1 Ω
C82-6 (VC) - C90-14 (VCM) Always Below 1 Ω
C82-4 (E2) - C90-15 (E2M) Always Below 1 Ω
C82-3 (E2S) - C90-8 (E2S) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C82-5 (PR) or C90-16 (PCR1) - Body ground Always 10 kΩ or higher
C82-2 (PR2) or C90-2 (PCR2) - Body ground Always 10 kΩ or higher
C82-1 (VCS) or C90-13 (VCS) - Body ground Always 10 kΩ or higher
C82-6 (VC) or C90-14 (VCM) - Body ground Always 10 kΩ or higher
C82-4 (E2) or C90-15 (E2M) - Body ground Always 10 kΩ or higher
C82-3 (E2S) or C90-8 (E2S) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel pressure sensor connector.


e.

Reconnect the ECM connector.



OK

3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
U169119E02
2,1.333 2.469,1.573 false 1.427,1.021 1.063,0.781 false 1.948,1.021 2.313,0.74 false 1.427,1.323 0.99,1.646 false 0.219,0.146 0.417,0.323 0.198,0.177 10 false *a 2.531,1.5 2.813,1.677 0.281,0.177 10 false VC 0.729,0.677 1.094,0.854 0.365,0.177 10 false VCS 0.563,1.208 0.875,1.365 0.313,0.156 10 false C82 2.375,0.656 2.656,0.823 0.281,0.167 10 false E2S 0.781,1.583 0.99,1.74 0.208,0.156 10 false E2

a.

Disconnect the fuel pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C82-6 (VC) - C82-4 (E2) Ignition switch ON 4.5 to 5.5 V
C82-1 (VCS) - C82-3 (E2S) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to fuel pressure sensor)


c.

Reconnect the fuel pressure sensor connector.



OK

4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL)

NG

7.REPLACE ECM
4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL)
a.

Replace the common rail (See page Engine / Hybrid System>1KD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.


f.

Read the DTCs.

Result
Result Proceed to
P0087, P0190, P0192 or P0193 is output A
No DTC is output B



A

7.REPLACE ECM

B

END

7.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0087, P0190, P0192 and/or P0193.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.




NEXT

END