Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  


DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

P0488
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. The throttle motor activation duty is more than a specified value for 30 seconds (1 trip detection logic).
·

Throttle valve stuck

·

Throttle valve does not move smoothly

·

Open or short in throttle control motor circuit

·

ECM



Related Data List
DTC No. Data List
P0488
·

Throttle Motor Duty #1

·

Actual Throttle Position



Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

A128641E36
4.615,2.135 4.74,1.813 false 4.615,2.896 4.74,2.573 false 4.615,3.646 4.74,3.333 false 4.74,4.104 4.615,3.792 false 5.344,5.26 5.167,5.042 false 3.333,5.365 3.094,5.188 false 0.292,5.427 1.688,5.792 1.396,0.365 10 false Duty Ratio Malfunction Counter 0.135,0.063 1.917,0.271 1.781,0.208 10 false Malfunction Detection: 0.292,1.24 1.583,1.656 1.292,0.417 10 false Throttle Valve Target Opening Angle 0.292,2.708 1.625,3.135 1.333,0.427 10 false Throttle Valve Actual Opening Angle 0.948,4.115 1.688,4.333 0.74,0.219 10 false Duty Ratio 4.802,1.708 5.396,1.906 0.594,0.198 10 false Normal 4.802,2.479 5.552,2.677 0.75,0.198 10 false Abnormal 4.802,4.042 5.396,4.24 0.594,0.198 10 false Normal 4.802,3.24 5.552,3.438 0.75,0.198 10 false Abnormal 5.948,0.604 6.396,0.802 0.448,0.198 10 false Open 5.948,1.354 6.427,1.552 0.479,0.198 10 false Close 5.948,2.063 6.396,2.26 0.448,0.198 10 false Open 5.948,2.823 6.427,3.021 0.479,0.198 10 false Close 5.948,3.563 6.458,3.76 0.51,0.198 10 false 100% 5.948,4.323 6.292,4.521 0.344,0.198 10 false 0% 3.385,5.302 4.802,5.51 1.417,0.208 10 false Stores P0488 5.385,5.208 6.177,5.417 0.792,0.208 10 false Threshold 3.51,6.271 3.917,6.469 0.406,0.198 10 false Time

WIRING DIAGRAM

A221593E03
3.211,1.261 4.615,1.430 1.404,0.170 10 Throttle Control Motor 3.211,1.079 3.538,1.234 0.327,0.156 10 C74 1.808,0.509 2.533,0.679 0.725,0.170 10 EFI NO. 2 3.064,2.185 3.331,2.369 0.267,0.184 10 EFI 3.82,2.746 4.087,2.929 0.267,0.184 10 EFI 0.906,2.213 1.264,2.397 0.357,0.184 10 P/I-B 2.298,0.268 2.419,0.431 0.121,0.163 10 2 1.901,0.268 2.022,0.431 0.121,0.163 10 1 3.384,0.286 3.505,0.449 0.121,0.163 10 2 4.608,0.506 4.729,0.669 0.121,0.163 10 1 5.197,0.6 5.494,0.737 0.297,0.137 10 C92 5.19,2.431 5.487,2.568 0.297,0.137 10 G58 5.533,2.339 5.946,2.486 0.413,0.146 10 MREL 5.533,0.588 5.974,0.734 0.441,0.146 10 LUSL 5.254,0.425 5.426,0.590 0.172,0.165 10 15 5.261,2.265 5.440,2.430 0.179,0.165 10 11 4.458,1.914 4.581,2.080 0.123,0.165 10 4 4.467,2.26 4.591,2.425 0.123,0.165 10 2 2.688,2.269 2.811,2.435 0.123,0.165 10 3 2.693,1.905 2.816,2.070 0.123,0.165 10 1 2.641,2.433 2.841,2.589 0.200,0.156 10 1B 4.435,2.438 4.627,2.593 0.193,0.156 10 1B 4.43,2.077 4.617,2.232 0.187,0.156 10 1B 2.637,2.066 2.843,2.222 0.207,0.156 10 1C 0.787,2.919 1.266,3.099 0.479,0.180 10 Battery 5.957,3.376 6.317,3.523 0.360,0.147 10 ECM 2.73,3.138 4.572,3.477 1.842,0.339 10 No. 1 Integration Relay (Engine Room Relay Block) 3.37,0.755 3.491,0.918 0.121,0.163 10 3 3.6,0.845 3.938,0.991 0.339,0.146 10 RSC 3.609,0.366 3.730,0.513 0.121,0.146 10 B 4.193,0.611 4.513,0.758 0.320,0.146 10 RSO

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

Although the DTC titles say exhaust gas recirculation throttle position control Range / Performance, these DTCs relate to the throttle valve

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
a.
U169086E01
0.102,0.026 0.313,0.189 0.211,0.163 10 *a 0.458,1.222 0.752,1.392 0.294,0.170 10 C74 1.67,1.912 1.839,2.082 0.169,0.170 10 B 1.737,1.446 1.737,1.895 false

Disconnect the throttle control motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C74-2 (B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to throttle control motor)


c.

Reconnect the throttle control motor connector.



OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY)
2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Disconnect the throttle control motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C74-3 (RSC) - Body ground Always Below 1 Ω



c.

Reconnect the throttle control motor connector.



OK

3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
a.

Disconnect the throttle control motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C74-1 (RSO) - C92-15 (LUSL) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C74-1 (RSO) or C92-15 (LUSL) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle control motor connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS

b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Result Proceed to
P0488 is output A
No DTC is output B



A

6.REPLACE ECM

B

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY)
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P0488.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.




NEXT

END