Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

P0617
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

ST relay circuit

·

Park/neutral position switch assembly*1

·

Clutch start switch assrembly*2

·

ECM



*1: for Automatic Transmission

*2: for Manual Transmission

Related Data List
DTC No. Data List
P0617 Starter Signal

WIRING DIAGRAM

for Automatic Transmission:

A388915E01
0.615,0.354 0.927,0.552 0.313,0.198 10 false NE 0.458,0.708 0.938,0.917 0.479,0.208 10 false STAR 0.531,2.521 1.01,2.729 0.479,0.208 10 false STA 0.24,2.885 0.719,3.094 0.479,0.208 10 false G50 0.25,3.042 1.51,3.396 1.26,0.354 10 false Power Managemant Control ECU 0.917,0.49 1.229,0.688 0.313,0.198 10 false 4 0.938,0.844 1.25,1.042 0.313,0.198 10 false 3 0.927,2.646 1.24,2.844 0.313,0.198 10 false 2 3.125,1.229 3.594,1.417 0.469,0.188 10 false C159 3.135,1.396 4.438,1.76 1.302,0.365 10 false Park/Neutral Position Switch Assembly 2.135,5.177 2.615,5.385 0.479,0.208 10 false FL 2.219,5.948 2.781,6.156 0.563,0.208 10 false Battery 2.896,3.229 3.375,3.438 0.479,0.208 10 false ST 4.76,1.031 5.073,1.229 0.313,0.198 10 false 4 4.771,2.135 5.083,2.333 0.313,0.198 10 false 5 4.781,1.271 5.094,1.469 0.313,0.198 10 false B 4.781,1.865 5.094,2.063 0.313,0.198 10 false L 4.146,3.385 4.458,3.583 0.313,0.198 10 false 5 4.167,4.188 4.479,4.385 0.313,0.198 10 false 3 4.781,3.396 5.094,3.594 0.313,0.198 10 false 2 4.792,4.188 5.104,4.385 0.313,0.198 10 false 1 4.938,3.792 5.417,4 0.479,0.208 10 false ST 6.333,2.531 6.813,2.74 0.479,0.208 10 false STA 6.333,0.708 6.813,0.917 0.479,0.208 10 false NSW 6.333,0.344 6.813,0.552 0.479,0.208 10 false NEO 6.073,0.479 6.385,0.677 0.313,0.198 10 false 23 6.073,0.823 6.385,1.021 0.313,0.198 10 false 11 6.083,2.646 6.396,2.844 0.313,0.198 10 false 22 3.021,5.531 3.5,5.74 0.479,0.208 10 false D8 3.438,5.531 3.917,5.74 0.479,0.208 10 false D9 4.177,4.979 4.656,5.188 0.479,0.208 10 false D11 4.188,5.188 4.667,5.396 0.479,0.208 10 false D10 5.115,5.323 6.563,5.542 1.448,0.219 10 false *1: for 2.0 kW type 3.667,6.156 4.833,6.417 1.167,0.26 10 false Starter Assembly 3.01,5.292 3.323,5.49 0.313,0.198 10 false 1*1 3.427,5.292 3.74,5.49 0.313,0.198 10 false 1*2 3.844,4.948 4.156,5.146 0.313,0.198 10 false 1*1 3.865,5.177 4.177,5.375 0.313,0.198 10 false 1*2 5.146,5.635 6.448,5.885 1.302,0.25 10 false *2: for 2.7 kW type 6.458,2.906 6.938,3.115 0.479,0.208 10 false G184 6.469,3.094 6.948,3.302 0.479,0.208 10 false ECM

for Manual Transmission:

A388916E01
0.146,3.208 1.354,3.573 1.208,0.365 10 false Power Managemant Control ECU 0.146,3.031 0.604,3.229 0.458,0.198 10 false G50 6.469,2.885 6.927,3.083 0.458,0.198 10 false G184 6.49,3.083 6.948,3.281 0.458,0.198 10 false ECM 4.938,3.823 5.396,4.021 0.458,0.198 10 false ST 2.135,4.958 2.594,5.156 0.458,0.198 10 false FL 2.219,5.969 2.948,6.167 0.729,0.198 10 false Battery 0.615,0.354 1.073,0.552 0.458,0.198 10 false NE 2.906,3.229 3.365,3.427 0.458,0.198 10 false ST 0.458,0.708 0.917,0.906 0.458,0.198 10 false STAR 0.531,2.521 0.99,2.719 0.458,0.198 10 false STA 3.24,1.563 4.396,1.917 1.156,0.354 10 false Cluch Start Switch Assembly 3.25,1.385 4.406,1.573 1.156,0.188 10 false A40*1, r1*2 4.781,1.031 4.938,1.229 0.156,0.198 10 false 2 4.771,2.146 4.927,2.344 0.156,0.198 10 false 1 6.073,0.469 6.406,0.688 0.333,0.219 10 false 23 6.094,2.646 6.427,2.865 0.333,0.219 10 false 22 6.344,0.354 6.802,0.552 0.458,0.198 10 false NEO 6.344,2.521 6.802,2.719 0.458,0.198 10 false STA 3.719,6.177 6.167,6.375 2.448,0.198 10 false Starter Assembly 4.167,4.969 4.625,5.167 0.458,0.198 10 false D11 4.177,5.188 4.635,5.385 0.458,0.198 10 false D10 3.01,5.531 3.469,5.729 0.458,0.198 10 false D8 3.427,5.531 3.885,5.729 0.458,0.198 10 false D9 3,5.313 3.292,5.51 0.292,0.198 10 false 1*3 3.833,5.177 4.292,5.375 0.458,0.198 10 false 1*4 3.823,4.958 4.115,5.156 0.292,0.198 10 false 1*3 3.406,5.302 3.865,5.5 0.458,0.198 10 false 1*4 5.24,5.104 6.792,5.344 1.552,0.24 10 false *1: for LHD 5.24,5.406 6.792,5.646 1.552,0.24 10 false *2: for RHD 5.25,5.75 6.802,5.99 1.552,0.24 10 false *3: for 2.0 kW type 5.271,6.083 6.823,6.323 1.552,0.24 10 false *4: for 2.7 kW type

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON (for Automatic Transmission) B
ON (for Manual Transmission) C




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

4.INSPECT CLUTCH START SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).



OK

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and wait for at least 30 seconds.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B




A

7.CHECK ENTRY AND START SYSTEM (START FUNCTION)

B

END

7.CHECK ENTRY AND START SYSTEM (START FUNCTION)

OK

END

NG

REPAIR OR REPLACE ENTRY AND START SYSTEM