Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P1271  Fuel Regulator Circuit (EDU Drive)  P1272  Fuel Pressure Regulator Circuit  


DESCRIPTION

The ECM controls the internal fuel pressure of the common rail assembly by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail assembly. Also, the pressure discharge valve opens when the engine switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.

HINT:
·

For more information on the pressure discharge valve and common rail system, refer to System Description (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).

·

If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).



A208468E03
0.057,0.035 4.208,0.212 4.151,0.177 10 Pressure Discharge Valve Operation Due to Sudden Deceleration: 0.928,0.378 2.056,0.722 1.128,0.343 10 Accelerator Pedal Opening Angle 0.403,1.389 2.038,1.552 1.635,0.163 10 Pressure Discharge Valve 1.132,2.292 2.044,2.455 0.913,0.163 10 Fuel Pressure 2.595,0.546 2.980,0.709 0.385,0.163 10 Open 4.139,1.391 4.524,1.554 0.385,0.163 10 Open 2.595,1.156 3.077,1.319 0.482,0.163 10 Closed 4.139,0.722 4.659,0.885 0.519,0.163 10 Closed 4.22,2.134 6.133,2.276 1.913,0.142 10 w/o Pressure Discharge Valve 1.673,2.706 3.482,2.848 1.809,0.142 10 w/ Pressure Discharge Valve 2.079,3.063 3.430,3.226 1.350,0.163 10 Target Fuel Pressure 3.932,3.287 4.942,3.450 1.010,0.163 10 Time Reduction 3.323,3.528 3.674,3.677 0.350,0.149 10 Time 3.73,2.783 3.499,2.783 false 3.685,3 3.495,3.14 3.495,3.14 3.415,3.14 false 3.898,2.424 4.087,2.224 4.087,2.224 4.183,2.224 false

A362191E01
4.219,2.01 4.792,1.573 4.792,1.573 4.906,1.573 true 3.042,2.406 3.146,2.406 3.146,2.406 3.729,1.667 true 0.104,0.115 3.49,0.313 3.385,0.198 10 false Cross Section Diagram of Pressure Discharge Valve: 1.594,0.583 3.854,0.813 2.26,0.229 10 false Return to Fuel Tank (Low Pressure) 0.313,1.521 2.156,1.917 1.844,0.396 10 false From Common Rail Assembly (High Pressure) 2.667,2.313 3.115,2.521 0.448,0.208 10 false Valve 4.958,1.51 5.583,1.729 0.625,0.219 10 false Solenoid

P1271
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal When the condition below is met a certain number of times (0.5 seconds) (1 trip detection logic):
·

Open or short in pressure discharge valve circuit.


·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve (common rail assembly)



P1272
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times. The fuel pressure does not decrease while the engine is running
(1 trip detection logic)
·

Open or short in pressure discharge valve circuit (P1271 is stored simultaneously)

·

Pressure discharge valve (common rail assembly)

·

ECM



Related Data List
DTC No. Data List
P1271
P1272
·

Common Rail Pressure

·

Target Common Rail Pressure

·

Pressure Discharge Valve



HINT:
·

After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure.

·

P1271:

After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not output.

·

P1272:

After clearing the DTC, perform the following procedure 5 times, and then check that P1272 is not output: Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal.


Reference
Engine Speed Common Rail Pressure (kPa)
Idling Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure
3000 rpm (No engine load)

Results of Real-vehicle Check
Condition Common Rail Pressure (Idling) Common Rail Pressure (1 Second after Engine Stopped)
Pressure discharge valve normal 35000 kPa 500 kPa
Open in pressure discharge valve circuit 35000 kPa 30000 kPa


MONITOR DESCRIPTION

P1271 (Open or short in pressure discharge valve circuit):

This DTC is output when there is an open or short circuit in the pressure discharge valve circuit. When this DTC is output, the ECM enters fail-safe mode and restricts the engine output. The ECM stays in fail-safe mode until the engine switch is turned off.


P1272 (Pressure discharge valve stuck closed):

The pressure discharge valve opens when the common rail target fuel pressure decreases during deceleration, decreasing the fuel pressure in the common rail assembly. The ECM compares the speed that the fuel pressure decreases with the speed that the common rail target fuel pressure decreases.

When the ECM determines that the decreasing rate of the fuel pressure is smaller than the common rail target fuel pressure, the ECM determines that the valve is stuck closed or there is an injection or supply pump assembly malfunction (overpressure) and outputs this DTC.

When this DTC is output, the ECM enters fail-safe mode and restricts the engine output. The ECM stays in fail-safe mode until the engine switch is turned off.


WIRING DIAGRAM

A348538E26
0.719,1.844 1.177,2.042 0.458,0.198 10 false r9 0.729,2.052 2.583,2.281 1.854,0.229 10 false Pressure Discharge Valve 5.677,0.646 6.313,0.844 0.635,0.198 10 false PRV- 5.677,1.292 6.292,1.479 0.615,0.188 10 false PRV+ 5.979,1.813 6.438,2.01 0.458,0.198 10 false C150 5.99,1.99 6.448,2.188 0.458,0.198 10 false ECM 2.073,0.75 2.531,0.948 0.458,0.198 10 false 2 2.073,1.406 2.531,1.604 0.458,0.198 10 false 1 5.479,0.75 5.938,0.948 0.458,0.198 10 false 1 5.5,1.438 5.958,1.635 0.458,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:
·

After completing repairs, confirm that P1271 and/or P1272 does not recur.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK IF DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the pending DTCs.

Result
Result Proceed to
DTC P1272 is output A
DTC P1271 is output B
DTC P1271 and P1272 are output
Other DTCs are output C



A

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)

B

5.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE RESISTANCE)

C

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain /Engine and ECT / Utility / Pressure Discharge Valve Check.


d.

Select "Close to Open Check".


e.

Read the value of "Open and Engine OFF".

OK:

0.5 MPa or less


HINT:
·

When the system is normal, the value of "Open and Engine OFF" should be at or close to 0 MPa.

·

When the fuel pressure value of "Open and Engine OFF" does not become equal to or less than 0.5 MPa, the pressure discharge valve may be stuck closed.

·

When the fuel pressure values of "Close and Engine OFF" and "Open and Engine OFF" are both 0 MPa, the pressure discharge valve may be stuck open or there may be a fuel leak.

·

Perform "Always Closed Check" if the value is not 0 MPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.





OK

3.CHECK DTC OUTPUT (DTC P1272)

NG

10.REPLACE COMMON RAIL ASSEMBLY
3.CHECK DTC OUTPUT (DTC P1272)
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTC.

Result
Result Proceed to
DTC P1272 is output A
DTC is not output B



A

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY

B

END

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

11.BLEED AIR FROM FUEL SYSTEM
5.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE RESISTANCE)
a.

Inspect the common rail assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - ECM)

NG

10.REPLACE COMMON RAIL ASSEMBLY
6.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - ECM)
a.

Disconnect the pressure discharge valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r9-2 - C150-2 (PRV+) Always Below 1 Ω
r9-1 - C150-1 (PRV-) Always Below 1 Ω
r9-2 or C150-2 (PRV+) - Body ground and other terminals Always 10 kΩ or higher
r9-1 or C150-1 (PRV-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the pressure discharge valve connector.


e.

Reconnect the ECM connector.



OK

7.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

Result
GTS Display Result Proceed to
Pending DTC P1271 and/or P1272 is output B
All Readiness NORMAL A
ABNORMAL B

HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 5 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





B

8.REPLACE ECM

A

END

8.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Perform this 5 times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P1271 and/or P1272.


iii.

Check the DTC judgment result.

HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 5 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





NEXT

END