Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P20BB  Reductant Heater "A" Control Circuit Low  P20BC  Reductant Heater "A" Control Circuit High  


DESCRIPTION

Refer to DTC P202B (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P202B).

P20BB
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Reductant Pipe Heater (Active Test) When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more.
(1 trip detection logic)
·

Open or short in urea tube with heater assembly circuit

·

Urea tube with heater assembly

·

Urea pump control ECU



P20BC
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Reductant Pipe Heater (Active Test) When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more.
(1 trip detection logic)
·

Open or short in urea tube with heater assembly circuit

·

Urea tube with heater assembly

·

Urea pump control ECU



Related Data List
DTC No. Data List
P20BB
P20BC
Reductant Pipe Heater

WIRING DIAGRAM

A357971E04
5.291,1.424 5.650,1.627 0.360,0.202 10 HTL 5.287,2.053 5.730,2.255 0.443,0.202 10 EHTL 4.976,1.549 5.204,1.725 0.228,0.177 10 20 4.976,2.231 5.197,2.451 0.221,0.221 10 32 5.238,2.954 5.495,3.129 0.258,0.174 10 s3 5.228,3.118 6.801,3.283 1.573,0.165 10 Urea Pump Control ECU 2.204,1.549 2.369,1.760 0.165,0.211 10 1 2.213,2.146 2.429,2.325 0.216,0.179 10 2 1.698,1.306 2.171,1.487 0.473,0.181 10 HTUL 1.698,1.91 2.139,2.112 0.441,0.202 10 GND1 0.446,2.692 0.699,2.906 0.253,0.214 10 s1 0.427,2.884 2.891,3.096 2.464,0.211 10 Urea Tube with Heater Assembly

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT UREA TUBE WITH HEATER ASSEMBLY
a.

Disconnect the urea tube with heater assembly connector.


b.
A179479E04
0.15,0 0.658,0.304 0.508,0.304 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.39 to 7.81 Ω


Text in Illustration
*a Component without harness connected
(to Urea Tube with Heater Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - UREA PUMP CONTROL ECU)

NG

9.REPLACE UREA TUBE WITH HEATER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - UREA PUMP CONTROL ECU)
U169583E01
5.26,0.969 5.542,1.406 false 5.177,0.771 4.771,1.354 false 1.885,0.927 2.146,1.313 false 1.563,0.927 1.292,1.354 false 1.146,1.375 1.75,1.531 0.604,0.156 10 false GND1 2.052,1.365 2.833,1.521 0.781,0.156 10 false HTUL 4.344,1.385 5.052,1.615 0.708,0.229 10 false 20(HTL) 5.594,1.406 6.427,1.604 0.833,0.198 10 false 32(EHTL) 1.667,0.219 1.885,0.427 0.219,0.208 10 false s1 0.5,0.167 0.719,0.375 0.219,0.208 10 false *a 4.135,0.167 4.354,0.375 0.219,0.208 10 false *b 5.396,0.156 5.615,0.365 0.219,0.208 10 false s3

Text in Illustration
*a Front view of wire harness connector
(to Urea Tube with Heater Assembly)
*b Front view of wire harness connector
(to Urea Pump Control ECU)

a.

Disconnect the urea tube with heater assembly connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance::
Tester Connection Condition Specified Condition
s1-1(HTUL) - s3-20(HTL) Always Below 1 Ω
s1-2(GND1) - s3-32(EHTL) Always Below 1 Ω
s1-1(HTUL) or s3-20(HTL) - Body ground Always 10 kΩ or higher
s1-2(GND1) or s3-32(EHTL) - Body ground Always 10 kΩ or higher



OK

3.CLEAR DTC

NG

8.REPAIR OR REPLACE HARNESS AND CONNECTOR
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and wait for 30 seconds or more.



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Pipe Heater.


d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.


Result:
Result Proceed to
DTC P20BB or P20BC is output A
DTCs is not output B



A

5.REPLACE UREA PUMP CONTROL ECU

B

END

5.REPLACE UREA PUMP CONTROL ECU
a.

Replace the urea pump control ECU (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and wait for 30 seconds or more.



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Pipe Heater.


d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END

8.REPAIR OR REPLACE HARNESS AND CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CLEAR DTC
9.REPLACE UREA TUBE WITH HEATER ASSEMBLY
a.

Replace the urea tube with heater assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL).



NEXT

6.CLEAR DTC