An electric heater is provided inside the urea tank and urea pipe, as urea solution freezes at -11°C (12.2°F) or lower.
The heater thaws frozen urea solution and prevents further freezing, allowing the urea SCR system to be started even in cold environments.
The tank heater turns ON and OFF according to the value of the temperature sensor. The heater for the urea tube with heater assembly turns ON and OFF according to the value of the ambient temperature sensor.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Reductant Tank Heater (Active Test) | When the tank heater is operating, an open or short circuit occurs in the tank heater for 3 seconds or more.
(1 trip detection logic) |
·
Open or short in tank heater circuit ·
Tank heater (Urea Pump) ·
Urea pump control ECU |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Reductant Tank Heater (Active Test) | When the tank heater is operating, an open or short circuit occurs in the tank heater for 3 seconds or more.
(1 trip detection logic) |
·
Open or short in tank heater circuit ·
Tank heater (Urea Pump) ·
Urea pump control ECU |
| DTC No. | Data List |
|---|---|
| P202B
P202C |
Reductant Tank Heater |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the tank heater (urea pump) (See PageEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>INSPECTION).
OK
NG
Disconnect the tank heater (urea pump) connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| s2-9 (TH+) - s3-21 (HTT) | Always | Below 1 Ω |
| s2-11 (TH-) - s3-31 (EHTT) | Always | Below 1 Ω |
| s2-9 (TH+) or s3-21 (HTT) - Body ground and other terminals | Always | 10 kΩ or higher |
| s2-11 (TH-) or s3-31 (EHTT) - Body ground and other terminals | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Tank Heater (urea pump)) |
*b | Front view of wire harness connector
(to Urea Pump Control ECU) |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Tank Heater .
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P202B or P202C is output | A |
| DTCs is not output | B |
A
B
Replace the urea pump control ECU (See pageEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Tank Heater.
Perform the Active Test.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT
Repair or replace the harness or connector.
NEXT
Replace the urea pump (See pageEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL).
NEXT