Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM J

1GD-FTV ENGINE CONTROL  ECD SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), the battery voltage is applied to terminal IGSW of the ECM. The MREL output signal from ECM causes a current to flow to the coil, closing the contacts of the EFI MAIN1 relay and supplying power to terminal +B, +B2 and +B3 of the ECM.

WIRING DIAGRAM

A356869E01
0.651,4.989 1.156,5.150 0.506,0.161 10 Battery 2.828,4.169 4.294,4.345 1.466,0.175 10 No. 1 Integration Relay 2.672,2.932 3.787,3.124 1.116,0.191 10 EFI-MAIN NO. 1 3.756,3.627 4.616,3.837 0.860,0.210 10 EFI MAIN1 6.416,4.599 6.819,4.794 0.403,0.195 10 ECM 6.244,1.732 6.526,1.924 0.283,0.192 10 +B 6.244,3.291 6.766,3.486 0.522,0.195 10 MREL 6.244,0.602 6.746,0.796 0.502,0.195 10 IGSW 6.244,4.042 6.471,4.204 0.228,0.161 10 E1 5.957,3.852 6.150,4.013 0.193,0.161 10 1 5.907,3.102 6.100,3.263 0.193,0.161 10 14 5.971,2.048 6.136,2.209 0.165,0.161 10 3 4.854,0.431 5.020,0.592 0.165,0.161 10 7 4.842,0.979 5.008,1.140 0.165,0.161 10 3 2.149,0.963 2.314,1.124 0.165,0.161 10 6 2.142,3.091 2.308,3.253 0.165,0.161 10 3 1.14,1.047 1.305,1.208 0.165,0.161 10 8 5.828,0.607 6.241,0.769 0.413,0.161 10 G185 5.908,0.427 6.150,0.589 0.242,0.161 10 18 0.326,1.771 1.729,2.162 1.403,0.391 10 Power Management Control ECU 3.916,1.476 4.284,1.672 0.368,0.196 10 IG2 3.097,0.736 3.402,0.909 0.305,0.173 10 IG2 0.707,1.148 1.124,1.329 0.418,0.181 10 IG2D 0.326,1.608 0.700,1.780 0.374,0.172 10 G50 0.532,3.658 0.935,3.858 0.404,0.200 10 P/I-B 2.098,1.135 2.376,1.296 0.277,0.161 10 1J 6.244,2.243 6.651,2.429 0.408,0.186 10 +B2 5.971,1.55 6.150,1.711 0.179,0.161 10 2 5.828,1.737 6.241,1.899 0.413,0.161 10 G185 5.828,2.228 6.241,2.389 0.413,0.161 10 G185 5.828,2.779 6.241,2.940 0.413,0.161 10 G185 5.828,3.279 6.241,3.440 0.413,0.161 10 G184 5.828,4.04 6.241,4.201 0.413,0.161 10 C152 5.971,2.601 6.136,2.762 0.165,0.161 10 4 6.244,2.776 6.658,2.975 0.415,0.200 10 +B3 4.809,0.617 5.087,0.778 0.277,0.161 10 1J 4.809,1.156 5.087,1.317 0.277,0.161 10 1J 4.802,2.774 5.080,2.936 0.277,0.161 10 1J 4.788,3.293 5.066,3.454 0.277,0.161 10 1K 2.091,2.781 2.369,2.943 0.277,0.161 10 1C 2.098,3.286 2.376,3.447 0.277,0.161 10 1J 4.797,2.594 5.046,2.755 0.249,0.161 10 10 4.846,3.105 5.012,3.267 0.165,0.161 10 7 2.135,2.594 2.301,2.755 0.165,0.161 10 1 5.345,0.748 5.706,0.965 0.361,0.217 10 IGN

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (+B, +B2 AND +B3 TERMINAL VOLTAGE)
a.
A348466E01
2.833,0.365 3.208,0.615 0.375,0.25 1.771,0.365 2.146,0.615 0.375,0.25 2.156,1.719 3.021,0.99 true 2.667,1.719 3.094,0.99 true 3.135,1.719 3.156,0.99 true 1.292,1.729 2.156,1 true 2.854,0.406 3.25,0.604 0.396,0.198 10 false G185 1.792,0.406 2.177,0.594 0.385,0.188 10 false C152 2.927,1.75 3.396,1.969 0.469,0.219 10 false 2 (+B) 2.365,1.75 2.885,1.958 0.521,0.208 10 false 3 (+B2) 1.813,1.75 2.333,1.958 0.521,0.208 10 false 4 (+B3) 1.042,1.75 1.563,1.958 0.521,0.208 10 false 1 (E1) 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G185-2 (+B) - C152-1 (E1) Engine switch on (IG) 11 to 14 V
G185-3 (+B2) - C152-1 (E1) Engine switch on (IG) 11 to 14 V
G185-4 (+B3) - C152-1 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

OK

CHECK PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance::
Tester Connection Condition Specified Condition
C152-1 (E1) - Body ground Always Below 1 Ω



c.

Reconnect the ECM connector.



OK

3.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)
a.
A348466E02
2.813,0.344 3.219,0.583 0.406,0.24 1.771,0.344 2.177,0.583 0.406,0.24 3,1.729 3.219,1.125 true 1.833,1.75 2.146,1 true 2.854,0.385 3.229,0.573 0.375,0.188 10 false G185 1.813,0.385 2.177,0.573 0.365,0.188 10 false C152 2.667,1.781 3.354,1.969 0.688,0.188 10 false 18 (IGSW) 1.615,1.781 2.302,1.969 0.688,0.188 10 false 1 (E1) 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G185-18 (IGSW) - C152-1 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

4.CHECK TERMINAL VOLTAGE (MREL TERMINAL VOLTAGE)

NG

7.INSPECT NO. 1 INTEGRATION RELAY (IG2)
4.CHECK TERMINAL VOLTAGE (MREL TERMINAL VOLTAGE)
a.
A348466E03
2.313,0.344 2.688,0.583 0.375,0.24 1.771,0.344 2.146,0.583 0.375,0.24 2.823,1.688 2.375,1.073 true 1.906,1.708 2.156,0.99 true 2.344,0.385 2.75,0.573 0.406,0.188 10 false G184 1.813,0.385 2.177,0.552 0.365,0.167 10 false C152 1.719,1.729 2.167,1.896 0.448,0.167 10 false 1 (E1) 2.469,1.729 3.208,1.927 0.74,0.198 10 false 14 (MREL) 0.094,0.052 0.323,0.271 0.229,0.219 10 false *a

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G184-14 (MREL) - C152-1 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

5.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN1)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN1)
a.


OK

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI MAIN1)

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1K-7 - G184-14 (MREL) Always Below 1 Ω
1J-10 - G185-2 (+B) Always Below 1 Ω
1J-10 - G185-3 (+B2) Always Below 1 Ω
1J-10 - G185-4 (+B3) Always Below 1 Ω
1J-3 - Body ground Always Below 1 Ω
1K-7 - G184-14 (MREL) - Body ground and other terminals Always Below 1 Ω
1J-10 or G185-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
1J-10 or G185-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher
1J-10 or G185-4 (+B3) - Body ground and other terminals Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the ECM connector.



OK

9.CHECK TERMINAL VOLTAGE (NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT NO. 1 INTEGRATION RELAY (IG2)
a.


OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2)

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-7 - G185-18 (IGSW) Always Below 1 Ω
1J-3 - Body ground Always Below 1 Ω
1J-7 or G185-18 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the ECM connector.



OK

9.CHECK TERMINAL VOLTAGE (NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (NO. 1 INTEGRATION RELAY)
a.
U169115E02
0.594,1.135 0.958,1.323 0.365,0.188 10 false 1C 0.198,0.094 0.448,0.302 0.25,0.208 10 false *a

Remove the No. 1 integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Integration Relay)


c.

Reinstall the No. 1 integration relay.



OK

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the power management control ECU connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance::
Tester Connection Condition Specified Condition
G50-8 (IG2D) - 1J-6 Always Below 1 Ω
G50-8 (IG2D) or 1J-6 - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the power management control ECU connector.


e.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR