Refer to DTC P0087 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0087).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idling for 1 second or more | The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM |
| DTC No. | Data List |
|---|---|
| P0191 | ·
Common Rail Pressure ·
Target Common Rail Pressure |
Refer to DTC P0087 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0087).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.
Start the engine.
Check the change in the values for the data list items above when increasing the engine speed from idling to 3000 rpm with no load.
| Result | Proceed to |
|---|---|
| Common Rail Pressure is always 10000 kPa or less
or Common Rail Pressure is always 200000 kPa or higher |
A |
| Except above | B |
Normally, "Common Rail Pressure" is within 5000 kPa of "Target Common Rail Pressure".
A
B
Disconnect the fuel pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r8-5 (PR) - C151-18 (PCR1) | Always | Below 1 Ω |
| r8-2 (PR2) - C152-26 (PCR2) | Always | Below 1 Ω |
| r8-1 (VCS) - C152-33 (VCS) | Always | Below 1 Ω |
| r8-6 (VC) - C151-28 (VCM) | Always | Below 1 Ω |
| r8-4 (E2) - C151-19 (E2M) | Always | Below 1 Ω |
| r8-3 (E2S) - C152-25 (E2S) | Always | Below 1 Ω |
| r8-5 (PR) or C151-18 (PCR1) - Body ground and other terminals | Always | 10 kΩ or higher |
| r8-2 (PR2) or C152-26 (PCR2) - Body ground and other terminals | Always | 10 kΩ or higher |
| r8-1 (VCS) or C152-33 (VCS) - Body ground and other terminals | Always | 10 kΩ or higher |
| r8-6 (VC) or C151-28 (VCM) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the fuel pressure sensor connector.
Reconnect the ECM connector.
OK
NG
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0191 is output | A |
| No DTC is output | B |
A
B
Replace the common rail assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Let the engine idle for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0191 is output | A |
| No DTC is output | B |
A
B
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Let the engine idle for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT