While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more | Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph). (b) Engine speed is more than 1000 rpm. (c) STA signal is on. |
·
ST relay circuit ·
Park/neutral position switch assembly*1 ·
Clutch start switch*2 ·
ECM |
*1: for Automatic Transmission
*2: for Manual Transmission
| DTC No. | Data List |
|---|---|
| P0617 | Starter Signal |
for Automatic Transmission:
for Manual Transmission:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).
If this DTC is output, inspect the starter assembly.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.
| Condition | Starter Signal | Proceed to |
|---|---|---|
| Driving at 20 km/h (12.4 mph) or more | OFF | A |
| ON (for Automatic Transmission) | B | |
| ON (for Manual Transmission) | C |
A
(See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
B
C
Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
OK
NG
(See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
Repair or replace the harness or connector (STA signal circuit).
NEXT
Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).
OK
NG
Repair or replace the harness or connector (STA signal circuit).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0617 is output | A |
| DTCs are not output | B |
A
B
Check the entry and start system (for start function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).
OK
NG