Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053662 1GR-FE ENGINE MECHANICAL _0260494 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 83530 1.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

a.
A224725

Using a 24 mm deep socket wrench, remove the oil pressure switch.


Hide 89422 2.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

a.
A224726

Using a 19 mm deep socket wrench, remove the sensor.


b.

Remove the gasket from the sensor.


Hide 11415 3.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.
A273790

Remove the water drain cock plug from the water drain cock.


b.

Remove the water drain cock from the cylinder block.


Hide 4.REMOVE VVT SENSOR

a.
A224729

LH:

Remove the 2 bolts and 2 VVT sensors.


b.
A224728

RH:

Remove the 2 bolts and 2 VVT sensors.


Hide 5.REMOVE CRANKSHAFT POSITION SENSOR

a.
A224727

Remove the bolt and crankshaft position sensor.


Hide 15330B 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH

a.
A224731

LH:

Remove the 2 bolts and 2 oil control valves.


b.
A224730

RH:

Remove the 2 bolts and 2 oil control valves.


Hide 12185 7.REMOVE OIL FILLER CAP HOUSING

a.
A221161

Remove the oil filler cap.


b.

Remove the 2 nuts, oil filler cap housing and gasket.


Hide 16356 13.REMOVE REAR WATER BY-PASS JOINT

a.
A076534

Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.


b.

Remove the O-ring from the No. 1 water outlet pipe.


Hide 12204 15.REMOVE PCV VALVE SUB-ASSEMBLY

a.

Remove the PCV valve hose.


b.
A224732

Remove the PCV valve.


Hide 11202 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A226542

Remove the 12 bolts, seal washer, cylinder head cover and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A223665

Remove the 3 gaskets.


Hide 11201 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A226543

Remove the 12 bolts, seal washer, cylinder head cover and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A221164

Remove the 3 gaskets.


Hide 11193 19.REMOVE SPARK PLUG TUBE GASKET

A124195

a.

Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.

Text in Illustration
V100135

Pry


b.

Remove the 6 spark plug tube gaskets.

HINT:

Be careful not to damage the gasket when removing it as the removed gasket needs to be used when installing a new one.



Hide 89491 20.REMOVE ENGINE OIL LEVEL SENSOR (w/ Warmer)

Hide 12101A 21.REMOVE OIL PAN DRAIN PLUG

a.

Remove the drain plug and gasket.


Hide 12102A 22.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 23.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 12121 25.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A224779

Remove the 6 bolts and No. 1 oil pan baffle plate.


Hide 11381 26.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A076247E09
0.792,0.26 0.969,0.438 0.177,0.177 10 true *a

Remove the 5 bolts and 2 nuts.


b.

Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.

Text in Illustration
*a Pry

HINT:

Tape the screwdriver tip before use.



Hide 11381A 27.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A076248

Using a screwdriver and hammer, tap out the oil seal.

NOTICE:

Be careful not to damage the rear oil seal retainer.



Hide 11302 28.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16100 29.REMOVE WATER PUMP ASSEMBLY

a.
A221171

Remove the 8 bolts, water pump and gasket.


Hide 11301C 30.REMOVE FRONT CRANKSHAFT OIL SEAL

Hide 31.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the pulley set bolt.


b.
A222172E05
0.563,0.302 1,0.115 1,0.115 1.115,0.115 true 0.74,0.677 0.583,1.781 0.583,1.781 1.583,0.969 true 2.396,1.958 2.396,1.729 2.396,1.729 2.26,1.552 true 1.135,0.031 1.302,0.188 0.167,0.156 10 true *1 0.479,1.823 0.646,1.979 0.167,0.156 10 true *2 2.302,1.958 2.469,2.115 0.167,0.156 10 false *3

Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).

Text in Illustration
*1 Center Line
*2 Timing Mark
*3 Sensor Plate


c.
A384116E01
2.448,1.104 1.604,1.583 1.604,1.583 2.448,0.563 true 0.927,0.458 1.615,1.583 1.615,1.583 0.917,0.917 true 2.771,3.781 2.063,4.198 2.063,4.198 2.708,3.406 true 1.365,3.333 2.063,4.188 2.063,4.188 1.333,3.958 true 1.51,1.635 1.76,1.833 0.25,0.198 10 true *1 1.99,4.24 2.229,4.417 0.24,0.177 10 true *1

Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.

If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.

Text in Illustration
*1 Timing Mark


Hide 13540 32.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A124589E21
1.063,1.073 1.448,1.729 1.448,1.729 2.656,1.135 true 1.146,0.833 0.958,0.104 0.958,0.104 0.854,0.104 false 2.802,0.854 2.646,0.094 2.646,0.094 2.521,0.094 false 2.688,1.698 2.875,1.698 true 0.646,0.031 0.823,0.208 0.177,0.177 10 false *1 2.281,0.01 2.469,0.188 0.188,0.177 10 false *1 1.375,1.781 1.74,1.979 0.365,0.198 10 true *2 2.885,1.615 3.156,1.792 0.271,0.177 10 true *3

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

Text in Illustration
*1 Plunger
*2 Stopper Plate
*3 Pin


b.

Move the stopper plate downward to set the lock, and insert a pin of φ1.27 mm (0.0500 in.) into the stopper plate hole.


c.
A095165

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 33.REMOVE CHAIN TENSIONER SLIPPER

a.
A223730

Remove the chain tensioner slipper.


Hide 13506 34.REMOVE NO. 1 CHAIN SUB-ASSEMBLY

a.
A221173E05
1.073,0.104 0.979,0.104 0.979,0.104 0.51,0.271 true 0.656,0.74 0.615,1.604 0.615,1.604 1.542,0.969 true 2.479,1.688 2.375,1.688 2.375,1.688 2.26,1.531 false 1.083,0.01 1.281,0.198 0.198,0.188 10 true *1 0.5,1.646 0.677,1.813 0.177,0.167 10 true *2 2.51,1.604 2.688,1.771 0.177,0.167 10 true *3

Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.

Text in Illustration
*1 Center Line
*2 Timing Mark
*3 Sensor Plate


b.

Remove the pulley set bolt.


c.
A221174

Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.


d.
A384117E01
0.094,0.083 0.406,0.281 0.313,0.198 10 false *A

Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.


e.

Remove the chain sub-assembly.

Text in Illustration
*A for Bank 1


Hide 13581 35.REMOVE NO. 1 IDLE GEAR SHAFT

a.
A221175

Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


Hide 13561 36.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A223642

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13562 37.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A221176

Remove the 2 No. 2 chain vibration dampers.


Hide 13521 38.REMOVE CRANKSHAFT TIMING SPROCKET

a.
U147484

Remove the crankshaft timing sprocket.


Hide 39.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

a.
A221132E05
1.438,2.958 1.563,2.958 1.563,2.958 1.688,2.667 false 1.729,2.188 1.646,2.188 1.646,2.188 1.531,2.333 false 1.24,2.875 1.396,3.031 0.156,0.156 10 false *1 1.75,2.083 1.938,2.24 0.188,0.156 10 false *2 2.531,1.51 2.74,1.688 0.208,0.177 10 true *a

While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.

Text in Illustration
*1 Pin
*2 Plunger
*a Push


b.
A221177E01
0.452,0.131 0.777,0.331 0.325,0.200 10 SST 2.74,0 2.961,0.198 0.221,0.198 10 *a 0.596,1.55 0.817,1.747 0.221,0.198 10 *b 0.845,0.215 0.983,0.215 0.983,0.215 1.297,0.632 false

Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

SST
09922-10010  

Text in Illustration
*a Turn
*b Hold

NOTICE:

Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.



c.

Remove the 2 bolts and camshaft timing gear assembly together with the No. 2 chain.


Hide 13550 40.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A221178

Remove the bolt and No. 2 chain tensioner assembly.


Hide 41.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

a.
A129700E06
1.586,2.144 1.806,2.328 0.221,0.184 10 *a 1.507,3.083 1.704,3.258 0.198,0.174 10 *1 2.991,2.287 3.239,2.471 0.248,0.184 10 45° 1.116,2.54 1.625,3.049 1.625,3.049 2.506,2.574 false

Check that the camshafts are positioned as shown in the illustration.

Text in Illustration
*1 Knock Pin
*a Front View


b.
A221179E09
0.688,0.771 0.854,0.948 0.167,0.177 10 true 1 2.719,0.75 2.875,0.927 0.156,0.177 10 true 3 2.719,0.083 2.854,0.25 0.135,0.167 10 true 4 1.396,0.802 1.542,0.969 0.146,0.167 10 true 5 1.406,0.125 1.552,0.292 0.146,0.167 10 true 6 2.094,0.792 2.24,0.958 0.146,0.167 10 true 7 2.094,0.125 2.25,0.302 0.156,0.177 10 true 8 0.708,0.125 0.865,0.302 0.156,0.177 10 true 2

Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.


c.
A221180E05
1.031,1.188 1.167,1.344 0.135,0.156 10 true 5 1.01,0.583 1.146,0.74 0.135,0.156 10 true 6 0.854,0.083 0.99,0.24 0.135,0.156 10 true 4 3.083,0.052 3.219,0.208 0.135,0.156 10 true 1 2.417,0.073 2.594,0.229 0.177,0.156 10 true 10 2.385,0.594 2.563,0.75 0.177,0.156 10 true 12 2.417,1.188 2.594,1.344 0.177,0.156 10 true 11 3.063,0.583 3.198,0.74 0.135,0.156 10 true 3 1.74,0.115 1.875,0.271 0.135,0.156 10 true 7 1.719,0.594 1.854,0.75 0.135,0.156 10 true 9 1.729,1.188 1.865,1.344 0.135,0.156 10 true 8 3.01,1.229 3.167,1.417 0.156,0.188 10 true 2

Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 5 camshaft bearing caps.


e.

Remove the camshaft and No. 2 camshaft.


Hide 11103C 42.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

a.
A221181E05
0.396,2.188 0.521,2.188 0.521,2.188 0.573,2.125 false 1.51,3.021 1.51,2.771 true 2.635,2.719 2.635,2.646 2.635,2.646 2.333,2.5 true 2.979,2.667 2.979,2.573 2.979,2.573 3.125,2.24 true 0.219,2.104 0.375,2.292 0.156,0.188 10 false *1 1.427,3.031 1.604,3.219 0.177,0.188 10 true *1 2.563,2.729 2.719,2.917 0.156,0.188 10 false *1 2.896,2.688 3.052,2.875 0.156,0.188 10 false *1

Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.



Hide 43.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

a.
A221182E07
2.01,2.573 2.115,2.573 2.115,2.573 2.302,2.26 true 2.24,1.823 2.146,1.823 2.146,1.823 1.938,2.052 false 2.26,1.719 2.448,1.896 0.188,0.177 10 false *1 1.802,2.51 1.99,2.688 0.188,0.177 10 false *2 1.917,0.302 2.104,0.479 0.188,0.177 10 true *a

While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.

Text in Illustration
*1 Pin
*2 Plunger
*a Push


b.
A223637E09
2.677,0.271 2.479,0.271 2.479,0.271 1.583,0.833 true 2.719,0.188 3.094,0.396 0.375,0.208 10 false SST 0.302,0 0.5,0.219 0.198,0.219 10 false *a 2.99,1.229 3.188,1.448 0.198,0.219 10 false *b

Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

SST
09922-10010  

Text in Illustration
*a Turn
*b Hold

NOTICE:

Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.



c.

Remove the 2 bolts and camshaft timing gear together with the No. 2 chain.


Hide 13560A 44.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A221183

Remove the bolt and No. 3 chain tensioner assembly.


Hide 45.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
A223636E05
1.167,2.521 1.677,3.063 1.677,3.063 2.313,2.5 true 1.615,2.146 1.802,2.323 0.188,0.177 10 false *a 1.552,3.073 1.74,3.25 0.188,0.177 10 false *1 1.052,2.073 1.292,2.24 0.24,0.167 10 true 15°

Check that the camshafts are positioned as shown in the illustration.

Text in Illustration
*1 Knock Pin
*a Front View


b.
A221184E09
2.469,1.448 2.625,1.656 0.156,0.208 10 true 1 2.469,0.813 2.583,1.01 0.115,0.198 10 true 2 0.25,1.427 0.396,1.625 0.146,0.198 10 true 3 0.219,0.771 0.375,0.979 0.156,0.208 10 true 4 1.792,1.448 1.927,1.625 0.135,0.177 10 true 5 1.792,0.823 1.917,1 0.125,0.177 10 true 6 1.146,1.448 1.313,1.625 0.167,0.177 10 true 7 1.156,0.823 1.292,1.031 0.135,0.208 10 true 8

Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.


c.
A221185E05
0.281,0.573 0.417,0.729 0.135,0.156 10 true 5 1.75,0.635 1.885,0.792 0.135,0.156 10 true 8 2.427,1.188 2.563,1.344 0.135,0.156 10 true 4 1.813,1.75 1.979,1.906 0.167,0.156 10 true 9 2.51,1.74 2.646,1.896 0.135,0.156 10 true 3 3.24,1.375 3.375,1.531 0.135,0.156 10 false 1 3.26,0.656 3.396,0.813 0.135,0.156 10 false 2 0.25,1.104 0.385,1.26 0.135,0.156 10 false 7 0.281,1.771 0.417,1.927 0.135,0.156 10 false 6 1.021,0.625 1.198,0.781 0.177,0.156 10 true 11 0.979,1.083 1.188,1.26 0.208,0.177 10 true 13 1,1.729 1.177,1.885 0.177,0.156 10 true 12 1.719,1.177 1.896,1.375 0.177,0.198 10 true 10

Uniformly loosen and remove the 13 bearing cap bolts in several steps in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 5 camshaft bearing caps.


e.

Remove the No. 3 camshaft and No. 4 camshaft.


Hide 11104A 46.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A221186E05
0.281,2.219 0.5,1.844 0.5,1.844 0.594,1.844 true 1.635,2.75 1.719,2.75 1.719,2.75 1.719,3.052 true 2.708,2.188 2.802,2.188 2.802,2.188 2.906,2.083 true 0.615,1.75 0.802,1.906 0.188,0.156 10 false *1 1.438,2.656 1.625,2.813 0.188,0.156 10 true *1 2.521,2.104 2.708,2.26 0.188,0.156 10 true *1

Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.



Hide 13801 47.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 24 valve rocker arms from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 48.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 24 valve lash adjusters from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 49.REMOVE VALVE STEM CAP

a.

Remove the 24 valve stem caps from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 11115 52.REMOVE CYLINDER HEAD GASKET

Hide 11116 53.REMOVE NO. 2 CYLINDER HEAD GASKET

Hide 56.REMOVE CYLINDER BLOCK WATER JACKET SPACER

A225372

a.

Remove the 2 water jacket spacers from the cylinder head.

NOTICE:

Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.



Hide 57.REMOVE TAPER SCREW PLUG

NOTICE:

It is not necessary to remove a taper screw plug unless it is being replaced.


Hide 58.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


Hide 59.REMOVE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


Hide 60.REMOVE STUD BOLT

NOTICE:

It is not necessary to remove a stud bolt unless it is being replaced.