Home › Engine / Hybrid System › 1KD-FTV (ENGINE MECHANICAL) › DRIVE BELT › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053664 1KD-FTV ENGINE MECHANICAL _0260513 DRIVE BELT A

1KD-FTV ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

a.

Use the pulley set bolt of the tensioner to rotate the tensioner pulley clockwise, and then install the V belt.

A223510E01
5.674,1.034 5.857,1.221 0.183,0.187 10 *1 2.532,0.778 2.715,0.965 0.183,0.187 10 *1 2.453,0.275 2.636,0.462 0.183,0.187 10 *2 1.814,2.127 1.997,2.314 0.183,0.187 10 *3 1.735,0.666 1.918,0.852 0.183,0.187 10 *3 4.79,2.088 4.973,2.275 0.183,0.187 10 *4 2.186,1.71 2.369,1.897 0.183,0.187 10 *4 4.776,0.659 4.959,0.846 0.183,0.187 10 *4 2.335,1.398 2.518,1.585 0.183,0.187 10 *5 5.144,1.854 5.327,2.041 0.183,0.187 10 *6 1.901,1.465 2.084,1.652 0.183,0.187 10 *6 5.189,1.515 5.371,1.702 0.183,0.187 10 *7 5.209,0.147 5.392,0.333 0.183,0.187 10 *7 5.892,0.125 6.075,0.312 0.183,0.187 10 *5 0.802,0.056 0.985,0.242 0.183,0.187 10 *a 0.802,1.353 0.985,1.540 0.183,0.187 10 *b 4.208,0.056 4.391,0.242 0.183,0.187 10 *c 4.208,1.353 4.391,1.540 0.183,0.187 10 *d 2.538,1.725 2.720,1.912 0.183,0.187 10 *2 5.593,2.006 5.776,2.193 0.183,0.187 10 *2 5.585,0.66 5.768,0.847 0.183,0.187 10 *2 2.616,2.249 2.799,2.436 0.183,0.187 10 *1 5.655,2.372 5.838,2.558 0.183,0.187 10 *1 4.764,1.138 4.947,1.325 0.183,0.187 10 *3 5.154,1.038 4.993,1.194 4.993,1.194 4.939,1.194 false 4.783,2.487 4.969,2.677 0.186,0.190 10 *3 5.171,2.383 5.013,2.542 5.013,2.542 4.959,2.543 false 5.395,2.078 5.013,2.163 5.013,2.163 4.959,2.164 false 5.399,0.727 4.947,0.727 false 5.554,0.495 5.822,0.194 5.822,0.194 5.876,0.194 false 5.881,1.507 6.064,1.694 0.183,0.187 10 *5 5.543,1.877 5.811,1.576 5.811,1.576 5.865,1.576 false

Text in Illustration
*1 Crankshaft Pulley *2 Fan Pulley
*3 Generator *4 No. 2 Idler Pulley
*5 No. 3 Idler Pulley *6 Cooler Compressor
*7 Viscous Heater - -
*a Type A *b Type C
*c Type B *d Type D

NOTICE:

Make sure that the V belt is set properly on each pulley.



b.

Check that the indicator mark of the V-ribbed belt tensioner (See page Engine / Hybrid System>1KD-FTV (ENGINE MECHANICAL)>DRIVE BELT>INSPECTION).


Hide 87452A 2.INSTALL FRONT HEATER BRACKET (for Cold Area Specification Vehicles)

a.

Install the front heater bracket with the 2 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 51405A 3.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY