Home › Engine / Hybrid System › 1KD-FTV (ENGINE MECHANICAL) › ENGINE › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053664 1KD-FTV ENGINE MECHANICAL _0260516 ENGINE G

1KD-FTV ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK ENGINE IDLE SPEED AND MAXIMUM SPEED

HINT:
·

For more information about the intelligent tester, refer to its operator's manual.

·

If an intelligent tester is not available, use a tachometer's tester probe as a substitute.



a.

Connect the intelligent tester to the DLC3.


b.
A206183E07
0.75,1.885 0.875,1.885 0.875,1.885 1.052,1.469 false 0.115,0.104 0.313,0.302 0.198,0.198 10 false *a 0.438,1.792 0.76,1.969 0.323,0.177 10 false TAC

If a tester is not available, connect the tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


c.

Inspect the idle speed.

HINT:
·

Make sure that the engine is warmed up.

·

Make sure that the A/C switch is off.

·

w/ DPF:

Make sure that PM regeneration is not being performed.



i.

Start the engine and measure the idle speed.

Idle Speed:
Item Specified Condition
for Automatic Transmission 650 to 750 rpm
for Manual Transmission 610 to 710 rpm




d.

Inspect the maximum speed.

i.

Start the engine.


ii.

Fully depress the accelerator pedal.


iii.

Measure the maximum speed.

Maximum Speed:

4450 to 4750 rpm




e.

If the tester probe of a tachometer is connected to the DLC3, disconnect the tester probe together with SST from terminal 9 of the DLC3.


f.

Disconnect the intelligent tester from the DLC3.


Hide 2.INSPECT CYLINDER COMPRESSION PRESSURE

HINT:

Measure the compression pressure if the engine power is insufficient, oil is consumed excessively and/or fuel economy is poor.


a.

b.

Disconnect the 4 injector connectors.


c.

Crank the engine to expel soot and other foreign matter from the inside of the cylinder.


d.
A223512E01
1.422,0.242 2.389,0.242 false 1.93,1.428 2.76,1.428 false 2.408,0.157 2.591,0.331 0.183,0.173 10 *1 2.765,1.342 2.948,1.516 0.183,0.173 10 *2

Measure the compression pressure.

i.

Install SST (attachment) to the glow plug hole.

SST
09992-00026  (09992-00121)

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

Text in Illustration
*1 SST (Compression Gauge)
*2 SST (Attachment)


ii.

Connect SST (compression gauge) to SST (attachment).

SST
09992-00026  (09992-00211)


iii.

Measure the compression pressure while cranking the engine.

HINT:

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.




e.

Perform the procedure above for each cylinder.

Standard compression pressure:

2700 kPa (27.5 kgf/cm2, 391 psi) or higher


Minimum pressure:

2200 kPa (22.5 kgf/cm2, 320 psi)


Standard difference between each cylinder:

500 kPa (5.0 kgf/cm2, 71 psi) or less


NOTICE:

This measurement must be done in as short a time as possible.


If the compression in one or more cylinders is low, add a small amount of engine oil into the glow plug hole. Then, repeat the procedure above for the low-compression cylinder(s).

HINT:
·

If poor compression improves after adding engine oil, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure remains low, a valve may be stuck or seated improperly, or pressure may be dropping due to leakage through the gasket.




f.

Remove SST (attachment and compression gauge).


g.

Connect the 4 injector connectors.