Home › Engine / Hybrid System › 1KD-FTV (FUEL) › FUEL SUPPLY PUMP › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053669 1KD-FTV FUEL _0260576 FUEL SUPPLY PUMP A

1KD-FTV FUEL  FUEL SUPPLY PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the fuel inlet pipe, clean them with a brush and compressed air.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 13568 2.REMOVE TIMING BELT

Hide 44360 4.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

a.
A223237

Remove the 3 bolts and disconnect the vane pump oil reservoir.


Hide 87208A 5.DISCONNECT HEATER WATER PIPE SUB-ASSEMBLY

Hide 25709E 6.DISCONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

Hide 23804C 8.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

a.
A152732

Remove the bolt and clamp.


b.
A152733E02
0.036,0.257 0.232,0.407 0.196,0.150 10 *a 0.036,2.328 0.232,2.478 0.196,0.150 10 *b

Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.

Text in Illustration
*a Common Rail Side
*b Fuel Supply Pump Side


Hide 22815A 9.REMOVE FUEL SUPPLY PUMP INSULATOR

A223244

Hide 22813 10.REMOVE NO. 1 FUEL SUPPLY PUMP PROTECTOR

a.
A223246

Remove the 2 bolts and No. 1 fuel supply pump protector.


Hide 22100 11.REMOVE FUEL SUPPLY PUMP ASSEMBLY

a.
A228335

Disconnect the 2 fuel hoses.


b.
A228336

Disconnect the fuel temperature sensor connector and suction control valve connector.


c.
A070710E02
1.094,0.948 1.25,1.146 0.156,0.198 10 false .

Remove the 4 bolts indicated by the arrows in the illustration.


d.

Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.


e.
A070711E11
1.146,0.99 0.885,1.854 0.885,1.854 1.646,1.51 true 0.729,1.875 1.104,2.073 0.375,0.198 10 false SST

Remove the set nut and O-ring while holding the crankshaft pulley using SST.

SST
09213-58014  
09330-00021  


f.
A228337

Loosen the 2 nuts.


g.
A070714E09
2.115,0.771 2.76,0.771 true 2.802,0.677 3.156,0.875 0.354,0.198 10 false SST

Using SST, disconnect the fuel supply pump from the supply pump gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021)

NOTICE:

Apply lubricant to the threads and tip of SST (center bolt) before using it.



h.

Remove the 2 nuts and fuel supply pump.

NOTICE:
·

Do not hold or carry the fuel supply pump by holding the pipe.

·

The fuel supply pump must be kept horizontal.




i.

Remove the O-ring.