1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
2.REMOVE REAR SEAT ASSEMBLY LH
for 60/40 Split Double-folding Seat Type LH Side:
for 60/40 Split Slide Walk-in Seat Type LH Side:
58371F
3.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
67934
4.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)
67918D
5.REMOVE REAR DOOR SCUFF PLATE LH
58325E
6.REMOVE REAR FLOOR SERVICE HOLE COVER
Remove the 3 screws and rear floor service hole cover.
Disconnect the fuel pump and sender gauge connector.
| *A | for Single Tank Type |
| *B | for Double Tank Type |
77606
7.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
for Type A:
Remove the 6 bolts and No. 1 fuel tank protector sub-assembly.
for Type B:
Remove the 4 bolts and No. 1 fuel tank protector sub-assembly.
77209D
8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)
Disconnect the fuel tank main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77207A
9.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)
Disconnect the fuel return tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77209D
10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
Disconnect fuel tank main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
11.DISCONNECT FUEL CUT OFF TUBE (for Single Tank Type)
Disconnect the fuel cut off tube (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77012
12.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)
Disconnect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77208A
13.DISCONNECT NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)
Disconnect the No. 4 fuel main tube sub-assembly and fuel suction tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
14.DISCONNECT FUEL CUT OFF TUBE (for Double Tank Type)
Disconnect the fuel cut off tube (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77207A
15.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
Disconnect the fuel return tube sub-assembly and No. 2 fuel main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77012
16.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)
Disconnect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77213B
17.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the clamp and disconnect the fuel tank to filler pipe hose from the filler pipe.
77100U
18.REMOVE FUEL TANK SUB-ASSEMBLY
Place a transmission jack under the fuel tank sub-assembly.
Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.
Slowly lower the transmission jack slightly.
77651A
19.REMOVE FUEL TANK CUSHION
Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank sub-assembly.
| *1 | No. 1 Fuel Tank Cushion |
| *2 | No. 2 Fuel Tank Cushion |
| *3 | No. 3 Fuel Tank Cushion |
77207A
20.REMOVE FUEL RETURN TUBE SUB-ASSEMBLY AND FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)
Remove the 2 fuel tube joint clips and pull out the fuel return tube sub-assembly and fuel tank main tube sub-assembly.
| *1 | Fuel Tube |
| *2 | Fuel Tube Joint |
| *3 | Fuel Tube Joint Clip |
| *4 | O-Ring |
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
Remove the fuel return tube sub-assembly and fuel tank main tube sub-assembly from the fuel tank sub-assembly.
77208A
21.REMOVE NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)
Remove the 2 fuel tube joint clips and pull out the No. 4 fuel main tube sub-assembly and fuel suction tube sub-assembly.
| *1 | Fuel Tube |
| *2 | Fuel Tube Joint |
| *3 | Fuel Tube Joint Clip |
| *4 | O-Ring |
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
Detach the clamp and remove the No. 4 fuel main tube from the fuel tank sub-assembly.
Detach the clamp and remove the fuel suction tube sub-assembly from the fuel tank sub-assembly.
77209D
22.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
Remove the 3 fuel tube joint clips and pull out the fuel tank main tube sub-assembly, fuel return tube sub-assembly and No. 2 fuel main tube sub-assembly.
| *1 | Fuel Tube |
| *2 | Fuel Tube Joint |
| *3 | Fuel Tube Joint Clip |
| *4 | O-Ring |
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
Detach the clamp and remove the No. 2 fuel main tube sub-assembly from the fuel tank sub-assembly.
Detach the clamp and remove the fuel return tube sub-assembly from the fuel tank sub-assembly.
Remove the fuel tank main tube sub-assembly from the fuel tank sub-assembly.
77010
23.REMOVE FUEL TANK VENT TUBE ASSEMBLY (for Single Tank Type)
Set SST on the retainer.
Engage the claws of SST securely with the retainer holes to secure SST.
Install SST while pressing the claws of SST against the retainer (towards the center of SST).
Using SST, loosen the retainer.
|
Turn |
Fit the tips of SST onto the ribs of the retainer.
When the retainer is loosened, be careful as the fuel tank vent tube assembly will spring upward from the force of the spring.
Remove any foreign matter around the fuel tank vent tube assembly before this operation.
Remove the retainer.
Remove the fuel tank vent tube assembly from the fuel tank sub-assembly.
Be careful not to bend the arm of the fuel sender gauge assembly.
Remove the gasket from the fuel tank sub-assembly.
77020A
24.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for Double Tank Type)
77643A
25.REMOVE NO. 3 FUEL TANK PROTECTOR
Remove the 2 bolts.
Detach the 4 clamps and remove the No. 3 fuel tank protector.
77213B
26.REMOVE FUEL TANK TO FILLER PIPE HOSE
Loosen the clamp and remove the fuel tank to filler pipe hose from the fuel tank sub-assembly.