Home › Engine / Hybrid System › 1KD-FTV (EMISSION CONTROL) › EGR VALVE › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053673 1KD-FTV EMISSION CONTROL _0260611 EGR VALVE A

1KD-FTV EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.



PROCEDURE

Hide 28800 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ EGR Cooler)

Hide 4.DRAIN ENGINE COOLANT (w/ EGR Cooler)

Hide 55781E 5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Remove the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 26100G 6.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16267 7.DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)

a.
A223447

Remove the clamp.


b.

Disconnect the No. 3 water by-pass hose from the EGR cooler.


Hide 16281 8.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)

a.

Disconnect the No. 4 water by-pass hose from the EGR cooler.


Hide 9.REMOVE INJECTION PIPE

NOTICE:
·

After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.

·

After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating the injector inlet.



a.
A223449

Remove the 2 nuts and No. 3 injection pipe clamp.


b.
A225331

Remove the 2 bolts and 2 No. 2 injection pipe clamps.


c.
A223451E01
0.042,0.052 0.26,0.271 0.219,0.219 10 true *a 0.052,2.417 0.323,2.625 0.271,0.208 10 true *b

Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.

Text in Illustration
*a for Injector Side
*b for Common Rail Side


Hide 17871A 10.REMOVE AIR CONNECTOR STAY

a.
A223452

Remove the 3 bolts and air connector stay.


Hide 82121 11.DISCONNECT ENGINE WIRE (for LHD)

a.
A225469

Remove the 2 bolts.


b.

Detach the clamp and disconnect the engine wire.


Hide 82121 12.DISCONNECT ENGINE WIRE (for RHD)

a.
A223453

Remove the bolt and disconnect the engine wire.


Hide 25625 13.REMOVE EGR VALVE BRACKET

a.

Remove the 2 nuts and EGR valve bracket.


Hide 14.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

a.
A223474

Disconnect the 2 connectors from the electric EGR control valve and E-VRV.


b.
A223455

Detach the wire harness clamp.


c.
A223475

Disconnect the 5 vacuum hoses.


d.

Remove the bolt and gas filter together with the gas filter bracket.


e.
A223476

Remove the 2 bolts and E-VRV bracket together with the EGR vacuum damper.


Hide 17862A 15.REMOVE NO. 2 INTAKE AIR CONNECTOR

a.
A223458

Remove the 3 nuts, No. 2 intake air connector and gasket.


Hide 17861F 16.REMOVE INTAKE AIR CONNECTOR

a.
A223478

Remove the 3 bolts, intake air connector and 2 gaskets.


Hide 25800 17.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

a.
A147220

Disconnect the No. 3 vacuum transmitting hose from the No. 2 EGR valve.


b.
A223461

Remove the bolt, 2 nuts, electric EGR control valve together with the No. 2 EGR valve and EGR cooler.


c.

Remove the gasket from the cylinder block.


Hide 25800 18.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 1 EGR PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.
A223479

Remove the 2 nuts and electric EGR control valve together with the No. 1 EGR pipe and gasket.


Hide 25800 19.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.
A223462E01
0.078,0 0.296,0.200 0.217,0.200 10 *A 0.078,2.301 0.296,2.501 0.217,0.200 10 *B

Remove the 2 bolts, electric EGR control valve and gasket.

Text in Illustration
*A w/ EGR Cooler
*B w/o EGR Cooler


Hide 25624 20.REMOVE EGR VALVE ADAPTER (w/ EGR Cooler)

a.
A223463

Using a 6 mm hexagon wrench, remove the 3 hexagon bolts, 3 plate washers, EGR valve adapter and gasket.


Hide 25630 21.REMOVE NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)

a.
A223464

Using a 5 mm hexagon wrench, remove the hexagon bolt, No. 2 EGR valve and gasket.