Home › Engine / Hybrid System › 1KD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053664 1KD-FTV ENGINE MECHANICAL _0260508 ENGINE ASSEMBLY A

1KD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 53301 2.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.
A222363

Remove the 8 bolts and hood.

NOTICE:

If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.



Hide 55781E 3.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Remove the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 52129B 4.REMOVE FRONT BUMPER LOWER COVER

a.

Remove the clip, 5 bolts and front bumper lower cover.


Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.

Remove the 4 bolts and No. 1 engine under cover.


Hide 51495 6.REMOVE TRANSMISSION UNDER COVER

a.

Remove the 2 bolts and transmission under cover.


Hide 51450 7.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

a.

Remove the 4 bolts and rear engine under cover.


Hide 10.DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 11.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 12.DRAIN POWER STEERING FLUID

Hide 16400 13.REMOVE RADIATOR ASSEMBLY

Hide 74481 14.REMOVE BATTERY HOLD DOWN CLAMP

a.

Remove the 2 nuts and battery hold down clamp.


Hide 28800 15.REMOVE BATTERY

Hide 74431 16.REMOVE BATTERY TRAY

Hide 17801 19.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 87120G 22.REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (for Cold Area Specification Vehicles)

a.

Disconnect the viscous heater connector.


b.
A223522

Disconnect the water by-pass hose and water hose.


c.
A223524

Remove the 2 bolts and viscous heater with magnet clutch.


Hide 87101 23.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

a.
A223525

Remove the 4 bolts and No. 1 viscous heater bracket.


Hide 88320 24.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

a.
A223526

Disconnect the compressor connector.


b.

Remove the 4 bolts and disconnect the cooler compressor.


Hide 26100 25.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 23300J 26.REMOVE FUEL FILTER ASSEMBLY

Hide 44306 27.DISCONNECT VANE PUMP OIL RESERVOIR SUB-ASSEMBLY

a.
A239651

Remove the 3 bolts and disconnect the vane pump oil reservoir.


Hide 44410 28.DISCONNECT PRESSURE FEED TUBE ASSEMBLY

a.
A224072

Disconnect the power steering oil pressure switch connector.


b.
A224081

Remove the union bolt and gasket and disconnect the pressure feed tube.


Hide 87245A 29.DISCONNECT INLET HEATER WATER HOSE

a.
A224071

Disconnect the inlet heater water hose.


Hide 87246A 30.DISCONNECT OUTLET HEATER WATER HOSE

a.
A223527

Disconnect the outlet heater water hose.


Hide 31.DISCONNECT FUEL HOSE

a.
A224080

Disconnect the No. 1 fuel hose and No. 2 fuel hose.


Hide 55501A 32.REMOVE GLOVE COMPARTMENT DOOR SUB-ASSEMBLY

a.

Hide 82121 33.DISCONNECT ENGINE WIRE

a.

Remove the No. 1 relay block cover.


b.
A224073

Remove the nut and detach the 2 claws.


c.
A224074

Disconnect the 3 injection driver connectors and remove the bolt.


d.
A224075

Disconnect the connector and detach the clamp.


e.
A224077

Remove the bolt.


f.
A224076

Remove the nut and disconnect the engine wire.


g.
A224078

Remove the bolt and disconnect the wire harness protector.


h.
A224079E01
0.116,0.069 0.334,0.264 0.218,0.195 10 *A 0.116,2.347 0.334,2.542 0.218,0.195 10 *B

Remove the bolt and disconnect the engine wire.

Text in Illustration
*A w/ KDSS
*B w/o KDSS


i.
A225400E01
0.04,0 0.275,0.221 0.235,0.221 10 *A 0.04,2.316 0.275,2.536 0.235,0.221 10 *B

Detach the clamp and disconnect the 9 connectors.

Text in Illustration
*A for LHD
*B for RHD


j.
A225401E04
2,0.063 2.208,0.25 0.208,0.188 10 true *B 0.073,0.063 0.281,0.25 0.208,0.188 10 true *A

Detach the grommet from the wire harness support.

Text in Illustration
*A for LHD
*B for RHD


k.
A225402E01
0.031,0 0.265,0.188 0.235,0.188 10 *A 1.83,0 2.064,0.188 0.235,0.188 10 *B

Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.

Text in Illustration
*A for LHD
*B for RHD


Hide 28100 34.REMOVE STARTER ASSEMBLY (for 2.2 kW Type)

Hide 28100 35.REMOVE STARTER ASSEMBLY (for 2.7 kW Type)

Hide 28100 36.REMOVE STARTER ASSEMBLY (for 3.0 kW Type)

Hide 12156 40.REMOVE OIL PAN INSULATOR

a.
A225336

Remove the 2 bolts and oil pan insulator.


Hide 41.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)

Hide 32101A 42.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)

Hide 43.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 12371 44.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.
A225338

Remove the 4 bolts and rear No. 1 engine mounting insulator.


Hide 45.REMOVE ENGINE ASSEMBLY

a.
A224109E01
0.802,0.865 1.188,0.26 1.188,0.26 1.292,0.26 true 2.708,0.781 3,0.26 3,0.26 3.073,0.26 true 1.354,0.167 1.563,0.344 0.208,0.177 10 false *1 3.135,0.167 3.344,0.344 0.208,0.177 10 false *2

Install 2 engine hangers with 2 bolts as shown in the illustration.

HINT:

Part No.


No. 1 engine hanger 12284-30020
No. 2 engine hanger 12282-67030
Bolt 91552-81014 and 91642-81030

Torque:
for No. 1 engine hanger : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for No. 2 engine hanger : 60 N*m (612 kgf*cm, 44 ft.*lbf)

Text in Illustration
*1 No. 1 engine hanger
*2 No. 2 engine hanger

NOTICE:

Install the engine hangers with new bolts.



b.

Attach an engine sling device and hang the engine with a chain block.


c.
A224146E01
0.104,0.083 0.354,0.302 0.25,0.219 10 true *A 0.104,2.427 0.344,2.625 0.24,0.198 10 true *B

Remove the 4 bolts and 4 nuts.

Text in Illustration
*A for LH Side
*B for RH Side


d.

Remove the engine by operating the engine sling device and chain block.


Hide 31210 46.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 47.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 48.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
A225337E01
1.156,0.99 0.74,0.99 true 2.156,0.917 2.521,1.198 2.521,1.198 2.521,1.302 true 0.406,0.906 0.74,1.083 0.333,0.177 10 true SST 2.396,1.313 2.729,1.479 0.333,0.167 10 true SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  
09330-00021  


b.

Remove the 8 bolts and flywheel.


Hide 32111 49.REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)

a.
A225337E01
1.156,0.99 0.74,0.99 true 2.156,0.917 2.521,1.198 2.521,1.198 2.521,1.302 true 0.406,0.906 0.74,1.083 0.333,0.177 10 true SST 2.396,1.313 2.729,1.479 0.333,0.167 10 true SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  
09330-00021  


b.
A225158

Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate, and the flywheel and ring gear.


Hide 11355 50.REMOVE REAR END PLATE

a.

Remove the bolt and rear end plate.


Hide 51.INSTALL ENGINE TO ENGINE STAND

Hide 82121 52.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine.


Hide 12361 53.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A224145E01
0.104,0.094 0.323,0.292 0.219,0.198 10 true *A 0.115,2.458 0.333,2.646 0.219,0.188 10 true *B

Disconnect the 2 hoses.

Text in Illustration
*A for LH Side
*B for RH Side


b.

Remove the 2 nuts and 2 front engine mounting insulators.