Home › Engine / Hybrid System › 2TR-FE (INTAKE / EXHAUST) › EXHAUST MANIFOLD
RM27T0E _51 Engine / Hybrid System _053676 2TR-FE INTAKE / EXHAUST _0260635 EXHAUST MANIFOLD A

2TR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17141 1.INSTALL EXHAUST MANIFOLD

a.
A355831

Install a new gasket.


b.
U147779E03
1.5,0.167 1.698,0.344 0.198,0.177 10 false 1 1.917,1.427 2.115,1.604 0.198,0.177 10 false 2 2.76,0.427 2.948,0.594 0.188,0.167 10 false 3 2.802,1.385 3.01,1.573 0.208,0.188 10 false 4 1.313,1.313 1.51,1.49 0.198,0.177 10 false 5 0.167,0.802 0.333,0.979 0.167,0.177 10 false 6 0.823,0.052 1.021,0.26 0.198,0.208 10 false 7 2.125,0.094 2.344,0.302 0.219,0.208 10 false 8

Install the exhaust manifold with 8 new nuts in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 17118 2.INSTALL MANIFOLD STAY

a.
U148475E04
0.823,1.604 0.958,1.76 0.135,0.156 10 false A 0.896,1.115 1.021,1.271 0.125,0.156 10 false B 2.729,1.146 2.854,1.302 0.125,0.156 10 false C

Install the manifold stay with the 3 bolts.

Torque:
for bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for bolt B : 44 N*m (449 kgf*cm, 32 ft.*lbf)
for bolt C : 30 N*m (360 kgf*cm, 22 ft.*lbf)


Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

41.5 mm (1.63 in.)


If the free length is less than the minimum, replace the compression spring.


b.
A076194E27
2.031,1.583 1.5,1.708 false 1.5,1.708 1.354,1.708 false 2.438,0.979 3.042,0.979 false 1.156,1.625 1.375,1.802 0.219,0.177 10 false *1 3.063,0.885 3.281,1.063 0.219,0.177 10 false *a

Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.

Text in Illustration
*1 Gasket
*a Wooden Block

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




c.

Install a new gasket.


d.

Connect the front exhaust pipe assembly to the exhaust pipe support.


e.

Install the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

Connect the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


g.

Connect the air fuel ratio sensor connector and attach the wire harness clamp.


h.

Connect the heated oxygen sensor connector and attach the wire harness clamp.


Hide 25710 4.INSTALL AIR SWITCHING VALVE ASSEMBLY

Hide 53736B 5.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

a.

Install the front No. 1 fender apron to frame seal RH with the 5 clips.


Hide 53736 6.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 5 clips.