Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU transmit the data for general vehicle control and the diagnosis function through the communication line.

The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU.

DTC Code DTC Detection Condition Trouble Area
U0235 While the vehicle speed is 50 km/h (31 mph) or more with the cruise control switch on, a communication stop between the millimeter wave radar sensor and driving support ECU continues for 1 second or more.
·

Harness or connector

·

Millimeter wave radar sensor assembly

·

Driving support ECU



WIRING DIAGRAM

E322668E02
1.604,3.573 4.313,3.906 2.708,0.333 10 false Millimeter Wave Radar Sensor Assembly 1.615,3.406 2.073,3.604 0.458,0.198 10 false A15 0.75,4.365 2.833,4.563 2.083,0.198 10 false : CAN Communication Line 5.208,3.823 5.667,4.021 0.458,0.198 10 false G119 5.219,3.969 6.604,4.156 1.385,0.188 10 false Driving Support ECU 1.958,2.125 2.115,2.323 0.156,0.198 10 false 5 2.188,2.24 2.646,2.438 0.458,0.198 10 false IGB 1.969,2.656 2.125,2.854 0.156,0.198 10 false 2 2.167,2.771 2.781,2.969 0.615,0.198 10 false SGND 2.906,2.813 3.521,3.01 0.615,0.198 10 false CA1P 5.302,2.792 5.917,2.99 0.615,0.198 10 false CA1P 2.906,2.281 3.521,2.479 0.615,0.198 10 false CA1N 5.313,2.302 5.927,2.5 0.615,0.198 10 false CA1N 3.385,2.135 3.542,2.333 0.156,0.198 10 false 3 3.396,2.646 3.552,2.844 0.156,0.198 10 false 4 5.01,2.156 5.25,2.344 0.24,0.188 10 false 18 5.01,2.646 5.323,2.844 0.313,0.198 10 false 40 5.01,3.104 5.323,3.302 0.313,0.198 10 false 25 5.313,3.229 5.771,3.427 0.458,0.198 10 false GND 5.021,1.083 5.333,1.281 0.313,0.198 10 false 30 5.313,1.177 5.469,1.375 0.156,0.198 10 false B 1.375,0.729 2.479,0.99 1.104,0.26 10 false ECU-IG NO. 1 2.729,0.563 4.49,0.823 1.76,0.26 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When the driving support ECU is replaced with a new one, initialization must be performed (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Confirm that the connector is securely connected, as a partially connected connector may be the cause of this DTC.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR)
NOTICE:

A DTC is stored when the following inspection is performed. Be sure to clear the DTC after performing this inspection.


a.

Disconnect the G119 ECU connector.


b.
U170761E02
2.042,3.542 2.344,4.031 false 1.802,1.313 1.354,1.896 false 0.344,0.229 0.583,0.417 0.24,0.188 10 false *a 0.344,2.646 0.583,2.833 0.24,0.188 10 false *b 1.563,0.396 1.948,0.583 0.385,0.188 10 false G119 1.604,2.688 1.896,2.875 0.292,0.188 10 false A15 2.24,4.063 2.531,4.229 0.292,0.167 10 false IGB 1.177,1.885 1.469,2.052 0.292,0.167 10 false B

Disconnect the A15 sensor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
G119-30 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A15-5 (IGB) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU)
*b Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU AND MILLIMETER WAVE RADAR SENSOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU AND MILLIMETER WAVE RADAR SENSOR - BODY GROUND)
a.

Disconnect the A15 sensor connector.


b.
U170762E02
1.604,3.542 1.917,4.031 false 1.302,1.313 1.656,1.896 false 0.344,0.229 0.583,0.417 0.24,0.188 10 false *a 0.344,2.646 0.583,2.833 0.24,0.188 10 false *b 1.563,0.406 1.948,0.594 0.385,0.188 10 false G119 1.604,2.698 1.896,2.885 0.292,0.188 10 false A15 1.667,4.073 2.146,4.24 0.479,0.167 10 false SGND 1.5,1.927 1.844,2.094 0.344,0.167 10 false GND

Disconnect the G119 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G119-25 (GND) - Body ground Always Below 1 Ω
A15-2 (SGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU)
*b Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR)

NG

REPAIR HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR)
a.

Disconnect the G119 ECU connector.


b.

Disconnect the A15 sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G119-18 (CA1N) - A15-3 (CA1N) Always Below 1 Ω
G119-40 (CA1P) - A15-4 (CA1P) Always Below 1 Ω
G119-18 (CA1N) or A15-3 (CA1N) - Body ground Always 10 kΩ or higher
G119-40 (CA1P) or A15-4 (CA1P) - Body ground Always 10 kΩ or higher




OK

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR HARNESS OR CONNECTOR

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).



NEXT

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Adjust the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

b.

Perform the following to make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


i.

Drive the vehicle at a speed of 50 km/h (31 mph) or more.


ii.

Turn the cruise control switch on.



c.


OK

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY IS DEFECTIVE)

NG