Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U1102  Lost Communication with Radar Sensor  


DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU transmit the data for general vehicle control and the diagnosis function through the communication line.

The driving support ECU estimates the curve information based on the signal from the steering wheel and yaw rate sensor.

The driving support ECU transmits the current vehicle speed and estimates curve information to the millimeter wave radar sensor assembly.

DTC Code DTC Detection Condition Trouble Area
U1102 While the vehicle speed is 50 km/h (31 mph) or more with the cruise control switch on, a communication stop between the millimeter wave radar sensor and driving support ECU continues for 1 second or more.
·

Harness or connector

·

Driving support ECU

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

E322668E03
1.625,3.573 4.229,3.802 2.604,0.229 10 false Millimeter Wave Radar Sensor Assembly 1.635,3.417 2.094,3.615 0.458,0.198 10 false A15 0.75,4.365 2.677,4.573 1.927,0.208 10 false : CAN Communication Line 5.208,3.833 5.667,4.031 0.458,0.198 10 false G119 5.219,3.979 6.802,4.229 1.583,0.25 10 false Driving Support ECU 1.958,2.125 2.115,2.323 0.156,0.198 10 false 5 2.188,2.24 2.646,2.438 0.458,0.198 10 false IGB 1.969,2.656 2.125,2.854 0.156,0.198 10 false 2 2.167,2.771 2.781,2.969 0.615,0.198 10 false SGND 2.906,2.813 3.521,3.01 0.615,0.198 10 false CA1P 5.302,2.792 5.917,2.99 0.615,0.198 10 false CA1P 2.906,2.281 3.521,2.479 0.615,0.198 10 false CA1N 5.313,2.302 5.927,2.5 0.615,0.198 10 false CA1N 3.385,2.135 3.542,2.333 0.156,0.198 10 false 3 3.396,2.646 3.552,2.844 0.156,0.198 10 false 4 5.01,2.156 5.25,2.344 0.24,0.188 10 false 18 5.01,2.646 5.323,2.844 0.313,0.198 10 false 40 5.01,3.104 5.323,3.302 0.313,0.198 10 false 25 5.313,3.229 5.771,3.427 0.458,0.198 10 false GND 5.021,1.083 5.333,1.281 0.313,0.198 10 false 30 5.313,1.177 5.469,1.375 0.156,0.198 10 false B 1.396,0.74 2.521,0.979 1.125,0.24 10 false ECU-IG NO. 1 2.729,0.563 4.156,0.781 1.427,0.219 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When the driving support ECU is replaced with a new one, initialization must be performed (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>INITIALIZATION).

·

When the millimeter wave radar sensor is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Confirm that the connector is securely connected, as a partially connected connector may be the cause of this DTC.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - BATTERY AND BODY GROUND)
NOTICE:

A DTC is stored when the following inspection is performed. Be sure to clear the DTC after performing this inspection.


a.
U170589E01
0.446,0.15 0.617,0.308 0.171,0.158 10 *a 1.58,0.347 1.846,0.496 0.266,0.150 10 A15 2.196,1.743 2.466,1.899 0.270,0.156 10 IGB 0.977,1.743 1.410,1.899 0.434,0.156 10 SGND 1.999,1.202 2.336,1.739 false 1.584,1.202 1.248,1.739 false

Disconnect the A15 sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A15-5 (IGB) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-2 (SGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - BODY GROUND)
a.
U170591E01
0.186,0.096 0.346,0.252 0.159,0.156 10 *a 1.543,0.431 1.903,0.575 0.360,0.144 10 G119 1.314,1.305 1.091,1.767 false 0.904,1.774 1.233,1.930 0.330,0.156 10 GND

Disconnect the G119 ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G119-25 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU)



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - DRIVING SUPPORT ECU)
a.

Disconnect the A15 sensor connector.


b.

Disconnect the G119 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-3 (CA1N) - G119-18 (CA1N) Always Below 1 Ω
A15-4 (CA1P) - G119-40 (CA1P) Always Below 1 Ω
A15-3 (CA1N) or G119-18 (CA1N) - Body ground Always 10 kΩ or higher
A15-4 (CA1P) or G119-40 (CA1P) - Body ground Always 10 kΩ or higher




OK

4.REPLACE DRIVING SUPPORT ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE DRIVING SUPPORT ECU
a.

Replace the driving support ECU (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

b.

Perform the following to make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


i.

Drive the vehicle at a speed of 50 km/h (31 mph) or more.


ii.

Turn the cruise control switch on.



c.


OK

END (DRIVING SUPPORT ECU IS DEFECTIVE)

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY