Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P0571  Stop Light Switch Circuit Malfunction  


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Upon receiving the signal, the ECM cancels cruise control. Even if there is a malfunction in the stop light signal circuit while cruise control is in operation, normal driving is maintained due to a fail-safe function.

When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and stop light switch, and the ECM cancels cruise control.

DTC Code DTC Detection Condition Trouble Area
P0571 The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
·

Stop light switch circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

E285068E04
0.162,0.6 1.159,0.767 0.996,0.167 10 from IG2 Relay 0.312,1.146 1.104,1.313 0.792,0.167 10 from Battery 1.98,1.37 2.391,1.535 0.411,0.165 10 STOP 2.062,0.786 2.338,0.952 0.276,0.165 10 IGN 3.091,0.497 3.204,0.662 0.113,0.165 10 5 4.302,0.628 4.400,0.793 0.098,0.165 10 4 3.098,1.057 3.196,1.222 0.098,0.165 10 1 4.315,1.422 4.444,1.587 0.128,0.165 10 2 2.85,2.124 3.117,2.283 0.267,0.158 10 A85 2.85,2.288 4.582,2.446 1.732,0.158 10 Stop Light Switch Assembly 6.009,2.234 6.350,2.381 0.341,0.147 10 ECM 5.852,1.511 6.140,1.662 0.288,0.151 10 STP 5.852,0.727 6.224,0.878 0.371,0.151 10 ST1- 5.558,0.623 5.753,0.762 0.195,0.139 10 34 5.857,2.063 6.140,2.207 0.283,0.144 10 G56 5.571,1.413 5.762,1.552 0.191,0.139 10 35 3.105,1.583 3.203,1.748 0.098,0.165 10 3 3.287,1.683 3.630,1.839 0.343,0.156 10 GND 3.294,0.597 3.450,0.753 0.156,0.156 10 B 3.294,1.158 3.450,1.314 0.156,0.156 10 B 4.05,0.716 4.206,0.872 0.156,0.156 10 L 4.057,1.501 4.213,1.657 0.156,0.156 10 L 0.099,0.023 1.158,0.227 1.059,0.205 12 for 1GR-FE:

E285068E02
0.162,0.6 1.159,0.767 0.996,0.167 10 from IG2 Relay 0.312,1.146 1.104,1.313 0.792,0.167 10 from Battery 1.98,1.37 2.391,1.535 0.411,0.165 10 STOP 2.062,0.786 2.338,0.952 0.276,0.165 10 IGN 3.091,0.497 3.204,0.662 0.113,0.165 10 5 4.302,0.628 4.400,0.793 0.098,0.165 10 4 3.098,1.057 3.196,1.222 0.098,0.165 10 1 4.315,1.422 4.444,1.587 0.128,0.165 10 2 2.85,2.124 3.117,2.283 0.267,0.158 10 A85 2.85,2.288 4.582,2.446 1.732,0.158 10 Stop Light Switch Assembly 6.009,2.234 6.350,2.381 0.341,0.147 10 ECM 5.852,1.511 6.140,1.662 0.288,0.151 10 STP 5.852,0.727 6.224,0.878 0.371,0.151 10 ST1- 5.622,0.623 5.718,0.762 0.096,0.139 10 9 5.857,2.063 6.140,2.207 0.283,0.144 10 G57 5.623,1.413 5.738,1.552 0.115,0.139 10 8 3.105,1.583 3.203,1.748 0.098,0.165 10 3 3.287,1.683 3.630,1.839 0.343,0.156 10 GND 3.294,0.597 3.450,0.753 0.156,0.156 10 B 3.294,1.158 3.450,1.314 0.156,0.156 10 B 4.05,0.716 4.206,0.872 0.156,0.156 10 L 4.057,1.501 4.213,1.657 0.156,0.156 10 L 0.099,0.023 1.158,0.227 1.059,0.205 12 for 1KD-FTV:

E285068E03
0.162,0.6 1.159,0.767 0.996,0.167 10 from IG2 Relay 0.312,1.146 1.104,1.313 0.792,0.167 10 from Battery 1.98,1.37 2.391,1.535 0.411,0.165 10 STOP 2.062,0.786 2.338,0.952 0.276,0.165 10 IGN 3.091,0.497 3.204,0.662 0.113,0.165 10 5 4.302,0.628 4.400,0.793 0.098,0.165 10 4 3.098,1.057 3.196,1.222 0.098,0.165 10 1 4.315,1.422 4.444,1.587 0.128,0.165 10 2 2.85,2.124 3.117,2.283 0.267,0.158 10 A85 2.85,2.288 4.582,2.446 1.732,0.158 10 Stop Light Switch Assembly 6.009,2.234 6.350,2.381 0.341,0.147 10 ECM 5.852,1.511 6.140,1.662 0.288,0.151 10 STP 5.852,0.727 6.224,0.878 0.371,0.151 10 ST1- 5.546,0.623 5.765,0.762 0.219,0.139 10 12 5.857,2.063 6.473,2.207 0.616,0.144 10 G185 5.558,1.413 5.753,1.552 0.195,0.139 10 13 3.105,1.583 3.203,1.748 0.098,0.165 10 3 3.287,1.683 3.630,1.839 0.343,0.156 10 GND 3.294,0.597 3.450,0.753 0.156,0.156 10 B 3.294,1.158 3.450,1.314 0.156,0.156 10 B 4.05,0.716 4.206,0.872 0.156,0.156 10 L 4.057,1.501 4.213,1.657 0.156,0.156 10 L 0.099,0.023 1.158,0.227 1.059,0.205 12 for 1GD-FTV:

CAUTION / NOTICE / HINT

NOTICE:
·

When the ECM is replaced with a new one, initialization must be performed (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BATTERY)
a.
U170685E02
1.323,1.354 0.708,1.438 false 2.156,1.344 2.771,1.417 false 1.729,1.417 1.927,1.844 false 1.646,0.188 1.938,0.354 0.292,0.167 10 false A85 0.073,0.031 0.25,0.198 0.177,0.167 10 false *a 0.552,1.365 0.677,1.521 0.125,0.156 10 false B 2.823,1.354 2.948,1.51 0.125,0.156 10 false B 1.74,1.854 2.073,2.01 0.333,0.156 10 false GND

Disconnect the A85 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A85-1 (B) - Body ground Always 11 to 14 V
A85-5 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
a.

Disconnect the A85 switch connector.


b.

Disconnect the G56*1, G57*2 or G185*2 ECM connectors.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE
Tester Connection Switch Condition Specified Condition
A85-4 (L) - G56-34 (ST1-) Always Below 1 Ω
A85-2 (L) - G56-35 (STP)
A85-4 (L) - Body ground Always 10 kΩ or higher
A85-2 (L) - Body ground

for 1KD-FTV
Tester Connection Switch Condition Specified Condition
A85-4 (L) - G57-9 (ST1-) Always Below 1 Ω
A85-2 (L) - G57-8 (STP)
A85-4 (L) - Body ground Always 10 kΩ or higher
A85-2 (L) - Body ground

for 1GD-FTV
Tester Connection Switch Condition Specified Condition
A85-4 (L) - G185-12 (ST1-) Always Below 1 Ω
A85-2 (L) - G185-13 (STP)
A85-4 (L) - Body ground Always 10 kΩ or higher
A85-2 (L) - Body ground




OK

3.CHECK STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Temporarily replace the stop light switch with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).




Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1KD-FTV) C
NG (for 1GD-FTV) D


A

END (STOP LIGHT SWITCH IS DEFECTIVE)

B

C

D